add Søren to CC On 1/25/09, scott.gasch_at_gmail.com <scott.gasch_at_gmail.com> wrote: > Hi Oliver, > > Thanks for the reply. I'm running bios version 02.61 American Megatrends > Inc; it has never been updated. I just got the latest image (1703) from > ASUS and will try flashing it. > > I don't have my controller set on RAID because I don't want hardware > RAID... it's set on AHCI instead. Maybe this is the difference. Are you > doing hardware RAID? > > I'm still looking over your config and dmesg, thanks for sending those. > I'll report back if I figure anything out. > > Thx, > Scott > > > On Jan 24, 2009 7:49am, Oliver Pinter <oliver.pntr_at_gmail.com> wrote: >> I have the same MB, and it running perfect, but I have only 3 SATA HDD >> >> + 1 SATA DVD-RW >> >> >> >> The ICH is in RAID mode. >> >> >> >> Attached my conf and dmesg >> >> >> >> Which version of BIOS use You? >> >> >> >> [snip] >> >> Southbridge >> >> - 6 x SATA 3Gb/s >> >> - Intel(R) Matrix Storage Technology with RAID 0, 1, 5, 10 support >> >> Marvell 88SE6121 >> >> - 1 x UltraDMA 133/100/66 for up to 2 PATA devices >> >> - 1 x External SATA 3Gb/s port (SATA On-the-Go) >> >> Silicon Image Sil5723 (Drive Xpert technology) >> >> - 2 x SATA 3Gb/s >> >> - Supports EZ Backup and Super Speed functions >> >> [snip] >> >> >> >> > http://www.asus.com/products.aspx?l1=3&l2=11&l3=709&l4=0&model=2267&modelmenu=2 >> >> >> >> /* sorry for bad english */ >> >> >> >> On 1/24/09, Scott Gasch scott.gasch_at_gmail.com> wrote: >> >> > Hi, >> >> > I've been running a 7.1-p1 (amd64) system and and seeing very high > interrupt >> >> > rates on irq19 which is shared between several devices. Over 60% of one >> >> > core is used responding to interrupts. The machine also hangs > frequently. >> >> > irq19 is shared by atapci1, atapci2, fwohci0 and uhci4... >> >> > the consensus response to my last question was that "it's probably the > ata >> >> > driver". >> >> > >> >> > Today I tried building and booting a GENERIC current kernel and got > another >> >> > piece of information. The freebsd-current GENERIC kernel does not boot; >> >> > shortly after probing the drives it says "Cannot setup DMA" several > times on >> >> > the console and hangs. >> >> > >> >> > This machine is an Asus P5Q-E... I believe it has two ATA controllers: >> >> > a Marvell >> >> > 88SE6121 and a Silicon Image SIL5723. Is one of these chipsets > generating >> >> > interrupts that the driver doesn't understand and/or properly dismiss? > Can >> >> > it be put into a legacy mode that works? This machine has problems in > 7.0, >> >> > 7.1 and current... I'm running out of ideas. >> >> > >> >> > Thx, >> >> > Scott >> >> > _______________________________________________ >> >> > freebsd-current_at_freebsd.org mailing list >> >> > http://lists.freebsd.org/mailman/listinfo/freebsd-current >> >> > To unsubscribe, send any mail > to "freebsd-current-unsubscribe_at_freebsd.org" >> >> > >> >Received on Tue Jan 27 2009 - 13:05:31 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:39:41 UTC