Re: bge problems when resuming

From: Gonzalo Nemmi <gnemmi_at_gmail.com>
Date: Fri, 17 Jul 2009 17:43:10 -0300
On Wednesday 15 July 2009 8:13:47 am Adam K Kirchhoff wrote:
> On Wednesday 15 July 2009 03:20:45 Paul B. Mahol wrote:
> > On 7/15/09, Adam K Kirchhoff <adamk_at_voicenet.com> wrote:
> > > Hello all,
> > >
> > > I have a Dell Latitude D610 laptop with 8.0-BETA1 installed.  I
> > > hadn't tried suspend/resume for a while and decided to give it a
> > > shot.  I was pleasantly surprised to see that I could suspend to
> > > ram, resume, and have a (relatively) working system (previously
> > > the display would never come back up and the serial console I had
> > > hooked up remained dead). Great job to everyone who helped make
> > > that possible.
> > >
> > > The only real issue that I seem to have now is that bge is
> > > completely unusable after resume.  Another individual seems to
> > > have reported similar problems with bge and resume, but he also
> > > had other issues that apparently trumped his networking issues:
> > >
> > > http://lists.freebsd.org/pipermail/freebsd-current/2009-July/0090
> > >23.html
> > >
> > > Like him, resuming from suspend gives me:
> > >
> > > Jul 14 12:35:53 scroll kernel: bge0: PHY write timed out (phy 1,
> > > reg 0, val 32768)
> > > Jul 14 12:35:53 scroll kernel: bge0: PHY read timed out (phy 1,
> > > reg 0, val 0xffffffff)
> > > Jul 14 12:35:53 scroll kernel: bge0: PHY write timed out (phy 1,
> > > reg 24, val 3072)
> > > Jul 14 12:35:53 scroll kernel: bge0: PHY write timed out (phy 1,
> > > reg 23, val 10)
> > > Jul 14 12:35:53 scroll kernel: bge0: PHY write timed out (phy 1,
> > > reg 21, val 12555)
> > > Jul 14 12:35:53 scroll kernel: bge0: PHY write timed out (phy 1,
> > > reg 23, val 8223)
> > > Jul 14 12:35:53 scroll kernel: bge0: PHY write timed out (phy 1,
> > > reg 21, val 38150)
> > > Jul 14 12:35:53 scroll kernel: bge0: PHY write timed out (phy 1,
> > > reg 23, val 16415)
> > > Jul 14 12:35:53 scroll kernel: bge0: PHY write timed out (phy 1,
> > > reg 21, val 5346)
> > > Jul 14 12:35:53 scroll kernel: bge0: PHY write timed out (phy 1,
> > > reg 24, val 1024)
> > > Jul 14 12:35:53 scroll kernel: bge0: PHY write timed out (phy 1,
> > > reg 24, val 7)
> > >
> > > And so on and so forth.
> > >
> > > I thought that compiling if_bge as a module, unloading it before
> > > suspend, and reloading it after resume, might get this working.
> > > However, doing a "kldload if_bge" after the resume does nothing. 
> > > Well, the module gets loaded, but the device doesn't show up.  No
> > > errors from kldload, and there is nothing new in dmesg.
> > >
> > > Before the suspend, the device shows up as:
> > >
> > > bge0_at_pci0:2:0:0:        class=0x020000 card=0x01821028
> > > chip=0x167714e4 rev=0x01 hdr=0x00
> > >     vendor     = 'Broadcom Corporation'
> > >     device     = 'NetXtreme Gigabit Ethernet PCI Express
> > > (BCM5750A1)' class      = network
> > >     subclass   = ethernet
> > >
> > > After resuming,  and reloading the module, it's:
> > >
> > > none1_at_pci0:2:0:0:       class=0x020000 card=0x01821028
> > > chip=0x167714e4 rev=0x01 hdr=0x00
> > >     vendor     = 'Broadcom Corporation'
> > >     device     = 'NetXtreme Gigabit Ethernet PCI Express
> > > (BCM5750A1)' class      = network
> > >     subclass   = ethernet
> > >
> > > If there are no ideas, I'll go ahead and open up a pr.  I assume
> > > this is just one bug, since both problems (the PHY issues and the
> > > inability to reload the driver) are both related to the network
> > > device.
> >
> > Put this lines into loader.conf and reboot.
> >
> > hw.pci.do_power_nodriver="3"
> > hw.pci.do_power_resume="1"
> >
> > Now, before suspend, unload if_bge and some another driver (sound
> > drivers are best candidate) and load sound driver again, suspend
> > and resume.
> > Now loading if_bge should make it succesfully attach.
>
> Unfortunately, after doing this, reloading the if_bge driver causes
> the laptop to completely lock up...  It gets as far as:
>
> bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, unknown ASIC
> rev. 0xffff>
> mem 0xdfdf0000-0xdfdfffff irq 16 at device 0.0 on pci2
>
> And then the entire machine hangs.  I'm on ttyv0, so I'd see any
> kernel panic, but nothing like that happens.  The screen stays on,
> but nothing else happens till I force a reboot.
>
> Adam

Hi Adam, Paul ...
I'm the "another individual" from you OP. 
I have the same problems you have regarding bge, but they weren't 
trumped .. I just had an order of priorities ;)

Anyways, I tried the solution Paul posted and, just as in your case, I 
got a hard lock too ...

I tried loading if_bge through /boot/loader.conf
Then issued a:

kldunload if_bge coretemp
acpiconf -s 3

machine suspended 

As soon as I woke it up I got the following message followed by a hard 
lock:

fwohci0: Phy 1394a available S400, 1 ports.
fwohci0: Link S400, max_rec 2048 bytes.
fwohci0: Initiate bus reset
fwohci0: fwohci_intr_core: BUS reset
fwohci0: fwohci_intr_core: node_id=0x00000000, SelfID Count=1, 
CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me)
firewire0: bus manager 0
fwohci0: unrecoverable error
bge0: <Broadmcom NetXtreme Ethernet Controller, unknown ASIC rev, 
0xffff> mem 0xf69f0000-0xf69fffff irq 17 at device 0.0 on pci9

All this happens on a Dell 1318, FreeBSD 8.0-BETA1, i386, Intel(R) 
Celeron(R) CPU 560_at_2.13GHz.

bge0_at_pci0:9:0:0:	class=0x020000 card=0x02861028 chip=0x171314e4 rev=0x02 
hdr=0x00
    vendor     = 'Broadcom Corporation'
    device     = 'Broadcom NetLink (TM) Fast Ethernet (BCM5906m)'
    class      = network
    subclass   = ethernet
    bar   [10] = type Memory, range 64, base 0xf69f0000, size 65536, 
enabled
    cap 01[48] = powerspec 3  supports D0 D3  current D0
    cap 03[50] = VPD
    cap 09[58] = vendor (length 120)
    cap 05[e8] = MSI supports 1 message, 64 bit enabled with 1 message
    cap 10[d0] = PCI-Express 1 endpoint max data 128(128) link x1(x1)

If somebody needs more info, just ask me for it and I'll try to answer 
as soon as I can.

Adam, if you do file a PR, please let me know so I can follow it.

Best Regards
-- 
Blessings
Gonzalo Nemmi
Received on Fri Jul 17 2009 - 18:43:16 UTC

This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:39:52 UTC