I netbooted 9.0 Beta and was going to try and install the system onto a raid1 mirror built with graid. However, neither sysinstall nor bsdinstall see it fully I have the box netbooted (Intel Matrix raid) i5# graid status -ags Intel-a5bbf622 OPTIMAL ada0 (ACTIVE (ACTIVE)) Intel-a5bbf622 OPTIMAL ada1 (ACTIVE (ACTIVE)) i5# I can newfs /dev/raid/r0 i5# ls -l /dev/raid/r0 crw-r----- 1 root operator 0, 98 Aug 5 10:43 /dev/raid/r0 i5# and mount it. However, speeds seem a bit slow, but I am not sure if thats to be expected. i5# dd if=/dev/zero of=/mnt/test bs=1024k count=100 100+0 records in 100+0 records out 104857600 bytes transferred in 13.996080 secs (7491926 bytes/sec) i5# i5# iostat -c 1000 ada0 ada1 tty ada0 ada1 cpu tin tout KB/t tps MB/s KB/t tps MB/s us ni sy in id 2 204 124.47 5 0.57 124.28 5 0.57 0 0 0 0 100 0 186 128.00 60 7.49 128.00 62 7.74 0 0 0 0 100 0 64 128.00 55 6.87 128.00 50 6.24 0 0 0 1 99 0 63 128.00 60 7.49 128.00 64 7.99 0 0 0 1 99 0 63 128.00 40 4.99 128.00 40 4.99 0 0 0 1 99 0 63 126.43 61 7.52 128.00 59 7.37 0 0 0 0 99 0 63 128.00 45 5.62 128.00 43 5.37 0 0 0 1 99 0 63 128.00 50 6.24 128.00 51 6.37 0 0 0 0 100 0 64 128.00 50 6.24 128.00 49 6.12 0 0 0 1 99 0 63 128.00 80 9.99 128.00 81 10.11 0 0 0 0 100 0 64 128.00 70 8.74 128.00 71 8.87 0 0 0 0 99 But when I run sysintall, it does not find any disks. If I run bsdinstall, it sees ada0 and ada1, but I cannot partition and label the raid partition. Am I supposed to just write to ada0 ? What is the best way to do it Guided just shows ada0 and ada1 The partition editor does show md0 4.0 MB malloc ada0 465 GB raid/r0 465 GB ada1 465 GB raid/r0 465 GB But I cannot label any of the r0 'disks' It comes up with Invalid argument. arg0 'Intel-a5bbf622' ada0 at ahcich0 bus 0 scbus0 target 0 lun 0 ada0: <WDC WD5002AALX-00J37A0 15.01H15> ATA-8 SATA 3.x device ada0: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes) ada0: Command Queueing enabled ada0: 476940MB (976773168 512 byte sectors: 16H 63S/T 16383C) ada0: Previously was known as ad4 ada1 at ahcich1 bus 0 scbus1 target 0 lun 0 ada1: <WDC WD5002AALX-00J37A0 15.01H15> ATA-8 SATA 3.x device ada1: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes) ada1: Command Queueing enabled ada1: 476940MB (976773168 512 byte sectors: 16H 63S/T 16383C) ada1: Previously was known as ad6 ahci0: <Intel ICH8 AHCI SATA controller> port 0x3068-0x306f,0x3074-0x3077,0x3060-0x3067,0x3070-0x3073,0x3020-0x303f mem 0xb2620000-0xb26207ff irq 18 at device 31.2 o n pci0 ahci0: AHCI v1.30 with 6 3Gbps ports, Port Multiplier not supported ahcich0: <AHCI channel> at channel 0 on ahci0 ahcich1: <AHCI channel> at channel 1 on ahci0 ahcich2: <AHCI channel> at channel 2 on ahci0 ahcich3: <AHCI channel> at channel 3 on ahci0 ahcich4: <AHCI channel> at channel 4 on ahci0 ahcich5: <AHCI channel> at channel 5 on ahci0 ---Mike -- ------------------- Mike Tancsa, tel +1 519 651 3400 Sentex Communications, mike_at_sentex.net Providing Internet services since 1994 www.sentex.net Cambridge, Ontario Canada http://www.tancsa.com/Received on Fri Aug 05 2011 - 14:01:07 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:40:16 UTC