Hi, I am trying to build a NanoBSD image for Soekris net4801 with a recent -CURRENT. The kernel boots fine but when it comes to mounting the root filesystem, it cannot find the flash disk anymore. Bios is up to date (1.33). The full boot -v log is below, here are the lines related to the ATA subsystem: atapci0: <National Geode SC1100 ATA33 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xe000-0xe00f at device 18.2 on pci0 ata0: <ATA channel> at channel 0 on atapci0 ata1: <ATA channel> at channel 1 on atapci0 ata: ata0 already exists; skipping it ata: ata1 already exists; skipping it ata0: reset tp1 mask=03 ostat0=50 ostat1=00 ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00 ata0: stat1=0x00 err=0x01 lsb=0x00 msb=0x00 ata0: reset tp2 stat0=50 stat1=00 devices=0x1 (aprobe0:ata0:0:0:0): SIGNATURE: 0000 (aprobe0:ata0:0:0:0): ATA status error (aprobe0:ata0:0:0:0): SETFEATURES SET TRANSFER MODE. ACB: ef 03 00 00 00 40 00 00 00 00 0c 00 (aprobe0:ata0:0:0:0): CAM status: ATA Status Error (aprobe0:ata0:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 04 (ABRT ) (aprobe0:ata0:0:0:0): RES: 51 04 00 00 00 00 00 00 00 0c 00 (aprobe0:ata0:0:0:0): Retrying command (aprobe0:ata0:0:0:0): ATA status error (aprobe0:ata0:0:0:0): SETFEATURES SET TRANSFER MODE. ACB: ef 03 00 00 00 40 00 00 00 00 0c 00 (aprobe0:ata0:0:0:0): CAM status: ATA Status Error (aprobe0:ata0:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 04 (ABRT ) (aprobe0:ata0:0:0:0): RES: 51 04 00 00 00 00 00 00 00 0c 00 (aprobe0:ata0:0:0:0): Error 5, Retries exhausted ata1: reset tp1 mask=00 ostat0=ff ostat1=ff (probe0:ctl2cam0:0:1:0): Error 6, Unretryable error Kernels up to FreeBSD 9 run fine on this box. Hope this can be solved, I have many of these devices in use and would really like to use the new carp(4) stuff in -CURRENT. Any ideas? With kind regards, Paul Schenkeveld [boot -v log] ------------------------------------------------------------------------ Copyright (c) 1992-2012 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 10.0-CURRENT #1 r232152: Sun Aug 12 17:20:11 CEST 2012 paul_at_localhost:/usr/obj/nanobsd.NET4801_10/i386.i386/FreeBSD/src-10/sys/NET4801_10_GEN i386 WARNING: WITNESS option enabled, expect reduced performance. Preloaded elf kernel "/boot/kernel/kernel" at 0xc14fd000. Calibrating TSC clock ... TSC clock: 266677901 Hz CPU: Geode(TM) Integrated Processor by National Semi (586-class CPU) Origin = "Geode by NSC" Id = 0x540 Family = 5 Model = 4 Stepping = 0 Features=0x808131<FPU,TSC,MSR,CX8,CMOV,MMX> real memory = 268435456 (256 MB) Physical memory chunk(s): 0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages) 0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages) 0x0000000001826000 - 0x000000000fb24fff, 238022656 bytes (58111 pages) avail memory = 239140864 (228 MB) bios32: Found BIOS32 Service Directory header at 0xc00f7800 bios32: Entry = 0xf7840 (c00f7840) Rev = 0 Len = 1 pcibios: PCI BIOS entry at 0xf0000+0x7861 Other BIOS signatures found: random device not loaded; using insecure entropy ULE: setup cpu 0 snd_unit_init() u=0x00ff8000 [512] d=0x00007c00 [32] c=0x000003ff [1024] feeder_register: snd_unit=-1 snd_maxautovchans=16 latency=5 feeder_rate_min=1 feeder_rate_max=2016000 feeder_rate_round=25 wlan: <802.11 Link Layer> kbd: new array size 4 kbd1 at kbdmux0 mem: <memory> nfslock: pseudo-device null: <null device, zero device> io: <I/O> random: <entropy source, Software, Yarrow> hptrr: RocketRAID 17xx/2xxx SATA controller driver v1.2 ACPI Error: A valid RSDP was not found (20120215/tbxfroot-237) ACPI: Table initialisation failed: AE_NOT_FOUND ACPI: Try disabling either ACPI or apic support. pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=00011078) pcibios: BIOS version 2.01 pcib0: <Host to PCI bridge> pcibus 0 on motherboard pci0: <PCI bus> on pcib0 pci0: domain=0, physical bus=0 found-> vendor=0x1078, dev=0x0001, revid=0x00 domain=0, bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0107, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x100b, dev=0x0020, revid=0x00 domain=0, bus=0, slot=6, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0107, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x3f (1890 ns), mingnt=0x0b (2750 ns), maxlat=0x34 (13000 ns) intpin=a, irq=10 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type I/O Port, range 32, base 0xe100, size 8, enabled map[14]: type Memory, range 32, base 0xa0000000, size 12, enabled found-> vendor=0x100b, dev=0x0020, revid=0x00 domain=0, bus=0, slot=7, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0107, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x3f (1890 ns), mingnt=0x0b (2750 ns), maxlat=0x34 (13000 ns) intpin=a, irq=10 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type I/O Port, range 32, base 0xe200, size 8, enabled map[14]: type Memory, range 32, base 0xa0001000, size 12, enabled found-> vendor=0x100b, dev=0x0020, revid=0x00 domain=0, bus=0, slot=8, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0107, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x3f (1890 ns), mingnt=0x0b (2750 ns), maxlat=0x34 (13000 ns) intpin=a, irq=10 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type I/O Port, range 32, base 0xe300, size 8, enabled map[14]: type Memory, range 32, base 0xa0002000, size 12, enabled found-> vendor=0x100b, dev=0x0510, revid=0x00 domain=0, bus=0, slot=18, func=0 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x001f, statreg=0x0280, cachelnsz=8 (dwords) lattimer=0x3f (1890 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[10]: type I/O Port, range 32, base 0x6100, size 6, enabled map[14]: type I/O Port, range 32, base 0x6200, size 6, enabled found-> vendor=0x100b, dev=0x0511, revid=0x00 domain=0, bus=0, slot=18, func=1 class=06-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[10]: type I/O Port, range 32, base 0x6300, size 8, enabled found-> vendor=0x100b, dev=0x0502, revid=0x01 domain=0, bus=0, slot=18, func=2 class=01-01-80, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[20]: type I/O Port, range 32, base 0xe000, size 4, enabled found-> vendor=0x100b, dev=0x0515, revid=0x00 domain=0, bus=0, slot=18, func=5 class=06-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0003, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[10]: type I/O Port, range 32, base 0x6500, size 6, enabled found-> vendor=0x0e11, dev=0xa0f8, revid=0x08 domain=0, bus=0, slot=19, func=0 class=0c-03-10, hdrtype=0x00, mfdev=0 cmdreg=0x0117, statreg=0x0280, cachelnsz=8 (dwords) lattimer=0x38 (1680 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 ns) intpin=d, irq=11 map[10]: type Memory, range 32, base 0xa0003000, size 12, enabled sis0: <NatSemi DP8381[56] 10/100BaseTX> port 0xe100-0xe1ff mem 0xa0000000-0xa0000fff irq 10 at device 6.0 on pci0 sis0: Silicon Revision: DP83816A miibus0: <MII bus> on sis0 nsphyter0: <DP83815 10/100 media interface> PHY 0 on miibus0 nsphyter0: OUI 0x1000e8, model 0x0002, rev. 1 nsphyter0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto sis0: bpf attached sis0: Ethernet address: 00:00:24:c6:e7:00 sis1: <NatSemi DP8381[56] 10/100BaseTX> port 0xe200-0xe2ff mem 0xa0001000-0xa0001fff irq 10 at device 7.0 on pci0 sis1: Silicon Revision: DP83816A miibus1: <MII bus> on sis1 nsphyter1: <DP83815 10/100 media interface> PHY 0 on miibus1 nsphyter1: OUI 0x1000e8, model 0x0002, rev. 1 nsphyter1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto sis1: bpf attached sis1: Ethernet address: 00:00:24:c6:e7:01 sis2: <NatSemi DP8381[56] 10/100BaseTX> port 0xe300-0xe3ff mem 0xa0002000-0xa0002fff irq 10 at device 8.0 on pci0 sis2: Silicon Revision: DP83816A miibus2: <MII bus> on sis2 nsphyter2: <DP83815 10/100 media interface> PHY 0 on miibus2 nsphyter2: OUI 0x1000e8, model 0x0002, rev. 1 nsphyter2: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto sis2: bpf attached sis2: Ethernet address: 00:00:24:c6:e7:02 isab0: <PCI-ISA bridge> port 0x6100-0x613f,0x6200-0x623f at device 18.0 on pci0 isa0: <ISA bus> on isab0 pci0: <bridge> at device 18.1 (no driver attached) atapci0: <National Geode SC1100 ATA33 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xe000-0xe00f at device 18.2 on pci0 ata0: <ATA channel> at channel 0 on atapci0 ata1: <ATA channel> at channel 1 on atapci0 pci0: <bridge> at device 18.5 (no driver attached) ohci0: <OHCI (generic) USB controller> mem 0xa0003000-0xa0003fff irq 11 at device 19.0 on pci0 ohci0: (New OHCI DeviceId=0xa0f80e11) usbus0: <OHCI (generic) USB controller> on ohci0 usbus0: bpf attached ohci0: usbpf: Attached cpu0 on motherboard ex_isa_identify() ahc_isa_probe 0: ioport 0xc00 alloc failed ahc_isa_probe 1: ioport 0x1c00 alloc failed ahc_isa_probe 2: ioport 0x2c00 alloc failed ahc_isa_probe 3: ioport 0x3c00 alloc failed ahc_isa_probe 4: ioport 0x4c00 alloc failed ahc_isa_probe 5: ioport 0x5c00 alloc failed ahc_isa_probe 6: ioport 0x6c00 alloc failed ahc_isa_probe 7: ioport 0x7c00 alloc failed ahc_isa_probe 8: ioport 0x8c00 alloc failed ahc_isa_probe 9: ioport 0x9c00 alloc failed ahc_isa_probe 10: ioport 0xac00 alloc failed ahc_isa_probe 11: ioport 0xbc00 alloc failed ahc_isa_probe 12: ioport 0xcc00 alloc failed ahc_isa_probe 13: ioport 0xdc00 alloc failed ahc_isa_probe 14: ioport 0xec00 alloc failed pnp_identify: Trying Read_Port at 203 pnp_identify: Trying Read_Port at 243 pnp_identify: Trying Read_Port at 283 pnp_identify: Trying Read_Port at 2c3 pnp_identify: Trying Read_Port at 303 pnp_identify: Trying Read_Port at 343 pnp_identify: Trying Read_Port at 383 pnp_identify: Trying Read_Port at 3c3 PNP Identify complete isa_probe_children: disabling PnP devices pmtimer0 on isa0 ata: ata0 already exists; skipping it ata: ata1 already exists; skipping it sc: sc0 already exists; skipping it isa_probe_children: probing non-PnP devices orm0: <ISA Option ROM> at iomem 0xc8000-0xd0fff pnpid ORM0000 on isa0 sc0: no video adapter found. sc0: <System console> failed to probe on isa0 vga0 failed to probe on isa0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 kbd0: atkbd0, generic (0), config:0x0, flags:0x1f0000 atkbd0: [GIANT-LOCKED] psm0: unable to allocate IRQ atrtc0: <AT realtime clock> at port 0x70 irq 8 on isa0 atrtc0: registered as a time-of-day clock (resolution 1000000us, adjustment 0.500000000s) Event timer "RTC" frequency 32768 Hz quality 0 attimer0: <AT timer> at port 0x40 on isa0 Timecounter "i8254" frequency 1193182 Hz quality 0 Event timer "i8254" frequency 1193182 Hz quality 100 fdc0 failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 ppc0: parallel port not found. ppc0: <Parallel port> failed to probe at irq 7 on isa0 uart0: <16550 or compatible> at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 uart0: fast interrupt uart0: console (9600,n,8,1) uart1: <16550 or compatible> at port 0x2f8-0x2ff irq 3 on isa0 uart1: fast interrupt isa_probe_children: probing PnP devices ctl: CAM Target Layer loaded Device configuration finished. procfs registered Timecounters tick every 1.000 msec vlan: initialized, using hash tables with chaining lo0: bpf attached hptrr: no controller detected. usbus0: 12Mbps Full Speed USB v1.0 ata0: reset tp1 mask=03 ostat0=50 ostat1=00 ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00 ata0: stat1=0x00 err=0x01 lsb=0x00 msb=0x00 ata0: reset tp2 stat0=50 stat1=00 devices=0x1 (aprobe0:ata0:0:0:0): SIGNATURE: 0000 ugen0.1: <0x0e11> at usbus0 uhub0: <0x0e11 OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0 (aprobe0:ata0:0:0:0): ATA status error (aprobe0:ata0:0:0:0): SETFEATURES SET TRANSFER MODE. ACB: ef 03 00 00 00 40 00 00 00 00 0c 00 (aprobe0:ata0:0:0:0): CAM status: ATA Status Error (aprobe0:ata0:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 04 (ABRT ) (aprobe0:ata0:0:0:0): RES: 51 04 00 00 00 00 00 00 00 0c 00 (aprobe0:ata0:0:0:0): Retrying command (aprobe0:ata0:0:0:0): ATA status error (aprobe0:ata0:0:0:0): SETFEATURES SET TRANSFER MODE. ACB: ef 03 00 00 00 40 00 00 00 00 0c 00 (aprobe0:ata0:0:0:0): CAM status: ATA Status Error (aprobe0:ata0:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 04 (ABRT ) (aprobe0:ata0:0:0:0): RES: 51 04 00 00 00 00 00 00 00 0c 00 (aprobe0:ata0:0:0:0): Error 5, Retries exhausted ata1: reset tp1 mask=00 ostat0=ff ostat1=ff uhub0: 3 ports with 3 removable, self powered (probe0:ctl2cam0:0:1:0): Error 6, Unretryable error WARNING: WITNESS option enabled, expect reduced performance. Trying to mount root from ufs:/dev/ad0s1a [ro]... mountroot: waiting for device /dev/ad0s1a ... Mounting from ufs:/dev/ad0s1a failed with error 19. Loader variables: vfs.root.mountfrom=ufs:/dev/ad0s1a vfs.root.mountfrom.options=ro Manual root filesystem specification: <fstype>:<device> [options] Mount <device> using filesystem <fstype> and with the specified (optional) option list. eg. ufs:/dev/da0s1a zfs:tank cd9660:/dev/acd0 ro (which is equivalent to: mount -t cd9660 -o ro /dev/acd0 /) ? List valid disk boot devices . Yield 1 second (for background tasks) <empty line> Abort manual input mountroot> ? List of GEOM managed disk devices: mountroot>Received on Sun Aug 12 2012 - 13:49:31 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:40:29 UTC