Re: using multiple interfaces for same Network Card

From: Yasir hussan <kolyasir_at_gmail.com>
Date: Tue, 12 Mar 2013 23:32:57 +0500
Yes, i want to use them as vlan interface, Does any one has used *vlandev*,
after seen this
http://www.cyberciti.biz/faq/howto-configure-freebsd-vlans-with-ifconfig-command/i
tried to use it as

ifconfig vlan11  create 10.10.11.1  255.255.255.0 vlan 11  vlandev arge0
ifconfig vlan12  create 10.10.12.1  255.255.255.0 vlan 12  vlandev arge0
ifconfig vlan13  create 10.10.13.1  255.255.255.0 vlan 13  vlandev arge0
ifconfig vlan14  create 10.10.14.1  255.255.255.0 vlan 14  vlandev arge0

i was expecting that it will create interfaces which will work under arge0,
and will able to ping from any pc, Does any one have used it, kindly guide
me about it

Thanks

On Tue, Mar 12, 2013 at 5:06 PM, Ian FREISLICH <ianf_at_clue.co.za> wrote:

> Yasir hussan wrote:
> > Thanks for notic but all the elebration was for make alias on one
> > interface but i want to have multiple interface, i can no where that
> > some one would have tring to creating new interfaces and using them,
> > or may be i am missing something, just send its solution if have,
> > solution should be for
>
> I still think you're confusing Linux semantics with FreeBSD semantics.
>
> On linux you would have:
> eth0      Link encap:Ethernet  HWaddr 00:1E:C9:53:0B:61
>           inet addr:10.0.0.1  Bcast:10.0.0.255  Mask:255.255.255.0
>           inet6 addr: fe80::21e:c9ff:fe53:b61/64 Scope:Link
>           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
>           RX packets:211328068 errors:0 dropped:0 overruns:0 frame:0
>           TX packets:368394006 errors:0 dropped:0 overruns:0 carrier:0
>           collisions:0 txqueuelen:1000
>           RX bytes:34065846811 (31.7 GiB)  TX bytes:476377525764 (443.6
> GiB)
>           Interrupt:169 Memory:e6000000-e6011100
>
> eth0:1    Link encap:Ethernet  HWaddr 00:1E:C9:53:0B:61
>           inet addr:10.0.1.1  Bcast:10.0.1.255  Mask:255.255.255.0
>           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
>           Interrupt:169 Memory:e6000000-e6011100
>
>
> On FreeBSD you would have:
>
> re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
>
> options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE>
>         ether 54:04:a6:96:0c:1e
>         inet 10.0.0.1 netmask 0xffffff00 broadcast 10.0.0.255
>         inet 10.0.1.1 netmask 0xffffff00 broadcast 10.0.1.255
>         media: Ethernet autoselect (1000baseT <full-duplex>)
>         status: active
>
> These are both the same thing.  Is there any particular reason that
> you want multiple interfaces?  I can't see a use for it beyond "it's
> what I'm used to seeing" unless they're VLAN interfaces.
>
> Ian
>
> --
> Ian Freislich
>
Received on Tue Mar 12 2013 - 17:33:03 UTC

This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:40:35 UTC