On Sat, Mar 21, 2015 at 8:17 AM, Anders Bolt-Evensen <andersbo87_at_icloud.com> wrote: > Do you mean to check dmesg -a while doing "vmstat -ia | grep ath0"? > I did run "wlandebug +scan", then ifconfig wlan0 up scan and then "vmstat > -ia | grep ath0". > The only output I got from "vmstat -ia | grep ath0" is: > irq18: ath0 21 0 > The second time I ran that last command I got > irq18: ath0 22 0 > > It is worth mentioning that wifi with this Atheros card works just fine on > Windows (I am using this wlan when typing this answer on Windows). > There is a button that seems to enable airplane mode, but pressing this > button does not seem to change anything as far as FreeBSD is concerned. > Other than that button I can't find any button that enables or disables > wifi. > > > On 3/21/2015 5:22 AM, Kevin Oberman wrote: > >> On Fri, Mar 20, 2015 at 4:31 PM, Adrian Chadd <adrian_at_freebsd.org> wrote: >> >> Hm, ok. either interrupts aren't working, or the thing is deaf. :( >>> >>> can you do that and then in another screen run vmstat -ia | grep ath0 ? >>> >>> I'd like to see if it's at least posting interrupts. >>> >>> Could a bad antenna connection (loose plug/broken conductor/pinch to >> chassis shorting to ground) explain this? Or would the hardware notice and >> report this in all cases? >> > Guess it depends on the laptop model, on my acer I do have Fn-F3 (antena icon) playing with with seems to have some effect: ugen1.4: <vendor 0x0489> at usbus1 (disconnected) ugen1.4: <vendor 0x0489> at usbus1 But I didn't loose connection. If relevant: ugen0.1: <XHCI root HUB 0x8086> at usbus0, cfg=0 md=HOST spd=SUPER (5.0Gbps) pwr=SAVE (0mA) ugen1.1: <EHCI root HUB Intel> at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (0mA) ugen2.1: <EHCI root HUB Intel> at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (0mA) ugen0.2: <Targus Soft-Touch Cordless Mouse SONiX> at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON (100mA) ugen1.2: <product 0x0024 vendor 0x8087> at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (0mA) ugen2.2: <product 0x0024 vendor 0x8087> at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (0mA) ugen0.3: <1.3M HD WebCam SuYin> at usbus0, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON (500mA) ugen1.3: <USB2.0-CRW Generic> at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON (500mA) ugen1.4: <product 0xe04e vendor 0x0489> at usbus1, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON (100mA) -- >> Kevin Oberman, Network Engineer, Retired >> E-mail: rkoberman_at_gmail.com >> _______________________________________________ >> freebsd-current_at_freebsd.org mailing list >> http://lists.freebsd.org/mailman/listinfo/freebsd-current >> To unsubscribe, send any mail to "freebsd-current-unsubscribe_at_freebsd.org >> " >> > > _______________________________________________ > freebsd-current_at_freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-current > To unsubscribe, send any mail to "freebsd-current-unsubscribe_at_freebsd.org" >Received on Sat Mar 21 2015 - 14:08:20 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:40:56 UTC