Dear Svatopluk, tried again with current, and I get (almost) the same: Nov 23 18:14:47 current kernel: ath0: ath_edma_rxbuf_alloc: nothing on rxbuf?! Nov 23 18:14:47 current kernel: ath0: ath_edma_rxfifo_alloc: Q1: alloc failed: i=0, nbufs=128? Nov 23 18:14:47 current kernel: ath0: ath_edma_rxbuf_alloc: nothing on rxbuf?! Nov 23 18:14:47 current kernel: ath0: ath_edma_rxfifo_alloc: Q1: alloc failed: i=1, nbufs=128? Ideas? Can I help? Thank you. Regards, --- José Pérez El 2015-11-23 13:45, Svatopluk Kraus escribió: > On Mon, Nov 23, 2015 at 1:12 PM, José Pérez <fbl_at_aoek.com> wrote: >> Hi, >> I am the (happy?) owner of an Atheros AR9565 which used to work just >> fine. >> >> I recently updated an old -current, and a flood of these messages >> bumped up: >> Nov 13 17:47:16 test kernel: ath0: ath_edma_rxbuf_alloc: nothing on >> rxbuf?! >> Nov 13 17:47:16 test kernel: ath0: ath_edma_rxfifo_alloc: Q1: alloc >> failed: >> i=24, nb >> ufs=128? >> >> # pciconf -lv | relevant_part >> ath0_at_pci0:1:0:0: class=0x028000 card=0x064211ad chip=0x0036168c >> rev=0x01 hdr=0x00 >> vendor = 'Qualcomm Atheros' >> device = 'QCA9565 / AR9565 Wireless Network Adapter' >> class = network >> >> # dmesg | relevant_part >> ath0: <Qualcomm Atheros AR9565> mem 0xf0800000-0xf087ffff irq 32 at >> device >> 0.0 on pci1 >> ath0: WB335 2-ANT card detected >> ar9300_attach: calling ar9300_hw_attach >> ar9300_hw_attach: calling ar9300_eeprom_attach >> ar9300_flash_map: unimplemented for now >> Restoring Cal data from DRAM >> Restoring Cal data from EEPROM >> Restoring Cal data from Flash >> Restoring Cal data from Flash >> Restoring Cal data from OTP >> ar9300_hw_attach: ar9300_eeprom_attach returned 0 >> ath0: [HT] enabling HT modes >> ath0: [HT] enabling short-GI in 20MHz mode >> ath0: [HT] 1 stream STBC receive enabled >> ath0: [HT] 1 RX streams; 1 TX streams >> ath0: AR9565 mac 704.1 RF5110 phy 2261.3 >> ath0: 2GHz radio: 0x0000; 5GHz radio: 0x0000 >> >> # ifconfig | relevant_part >> wlan0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu >> 1500 >> ether a4:db:30:ab:ad:ca >> inet 192.168.1.2 netmask 0xffffff00 broadcast 192.168.1.255 >> nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> >> media: IEEE 802.11 Wireless Ethernet MCS mode 11ng >> status: associated >> ssid myssid channel 6 (2437 MHz 11g ht/20) bssid >> de:ad:be:ee:ee:ef >> regdomain ETSI2 country ES indoor ecm authmode WPA2/802.11i >> privacy ON deftxkey UNDEF AES-CCM 2:128-bit AES-CCM 3:128-bit >> txpower 30 bmiss 7 scanvalid 60 protmode CTS ampdulimit 64k >> ampdudensity 4 shortgi wme burst roaming MANUAL >> groups: wlan >> >> >> >> Is there anything I can help with to improve this? Thank you. >> > > What revision do you use? If you use <r291142, r291192>, please, try > to update to r291193 or higher. > > Svatopluk Kraus > > > >> Regards, >> >> -- >> José Pérez >> _______________________________________________ >> freebsd-current_at_freebsd.org mailing list >> https://lists.freebsd.org/mailman/listinfo/freebsd-current >> To unsubscribe, send any mail to >> "freebsd-current-unsubscribe_at_freebsd.org" > _______________________________________________ > freebsd-current_at_freebsd.org mailing list > https://lists.freebsd.org/mailman/listinfo/freebsd-current > To unsubscribe, send any mail to > "freebsd-current-unsubscribe_at_freebsd.org"Received on Tue Nov 24 2015 - 21:51:03 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:41:01 UTC