With a -current kernel ( cvsupped today ) I can no longer boot. It hangs on the drives connected to the promis controller built into my MSI KT266 mobo. The messages are like ad2: READ command timeout tag=0 serv=0 - resetting Same for ad3. It tries falling back to pio mode but after that it hangs completely. I have tried putting hw.at.tags=0 in /boot/loader.conf as suggested in some older messages on this list but that dit not help. dmesg of a working kernel built 19-1-2003 is attached Copyright (c) 1992-2003 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.0-CURRENT #1: Sun Jan 19 15:50:33 MET 2003 paulz_at_trantor.vanderzwan.org:/raid/bsd/obj/raid/bsd/freebsd/src/sys/trantor Preloaded elf kernel "/boot/kernel.ok/kernel" at 0xc04b1000. Preloaded elf module "/boot/kernel.ok/acpi.ko" at 0xc04b10ac. Timecounter "i8254" frequency 1193182 Hz Timecounter "TSC" frequency 1405012013 Hz CPU: AMD Athlon(tm) XP 1600+ (1405.01-MHz 686-class CPU) Origin = "AuthenticAMD" Id = 0x662 Stepping = 2 Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> AMD Features=0xc0480000<MP,AMIE,DSP,3DNow!> real memory = 536805376 (511 MB) avail memory = 516407296 (492 MB) Initializing GEOMetry subsystem Pentium Pro MTRR support enabled npx0: <math processor> on motherboard npx0: flags 0x7 npx0: INT 16 interface acpi0: <AMIINT > on motherboard ACPI-0625: *** Info: GPE Block0 defined as GPE0 to GPE15 Using $PIR table, 10 entries at 0xc00f7d80 acpi0: power button is handled as a fixed feature programming model. Timecounter "ACPI-fast" frequency 3579545 Hz acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 acpi_cpu0: <CPU> on acpi0 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pcib1: <PCI-PCI bridge> at device 1.0 on pci0 pci1: <PCI bus> on pcib1 pci0: <display, VGA> at device 6.0 (no driver attached) pci0: <network, ethernet> at device 7.0 (no driver attached) sym0: <810a> port 0xd800-0xd8ff mem 0xdbfeff00-0xdbfeffff irq 10 at device 8.0 on pci0 sym0: No NVRAM, ID 7, Fast-10, SE, parity checking atapci0: <Promise ATA100 controller> port 0xc400-0xc43f,0xc800-0xc803,0xcc00-0xcc07,0xd000-0xd003,0xd400-0xd407 mem 0xdbfc0000-0xdbfdffff irq 11 at device 12.0 on pci0 ata2: at 0xd400 on atapci0 ata3: at 0xcc00 on atapci0 isab0: <PCI-ISA bridge> at device 17.0 on pci0 isa0: <ISA bus> on isab0 atapci1: <VIA 8233 ATA100 controller> port 0xff00-0xff0f at device 17.1 on pci0 ata0: at 0x1f0 irq 14 on atapci1 ata1: at 0x170 irq 15 on atapci1 uhci0: <VIA 83C572 USB controller> port 0xb800-0xb81f irq 10 at device 17.2 on pci0 usb0: <VIA 83C572 USB controller> on uhci0 usb0: USB revision 1.0 uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhub0: port error, restarting port 1 uhub0: port error, giving up port 1 uhub0: port error, restarting port 2 uhci1: <VIA 83C572 USB controller> port 0xbc00-0xbc1f irq 10 at device 17.3 on pci0 usb1: <VIA 83C572 USB controller> on uhci1 usb1: USB revision 1.0 uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered uhub1: port error, restarting port 1 ugen0: Genesys Logic USB Host To Host Bridge, rev 1.00/1.80, addr 2 uhci2: <VIA 83C572 USB controller> port 0xc000-0xc01f irq 10 at device 17.4 on pci0 usb2: <VIA 83C572 USB controller> on uhci2 usb2: USB revision 1.0 uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub2: 2 ports with 2 removable, self powered uhub2: port error, restarting port 2 uhub2: port error, giving up port 2 acpi_button1: <Sleep Button> on acpi0 atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 fdc0: cmd 3 failed at out byte 1 of 3 sio0 port 0x3f8-0x3ff irq 4 on acpi0 sio0: type 16550A sio1 port 0x2f8-0x2ff irq 3 on acpi0 sio1: type 16550A ppc0 port 0x778-0x77b,0x378-0x37f irq 7 drq 3 on acpi0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/9 bytes threshold lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port fdc0: cmd 3 failed at out byte 1 of 3 orm0: <Option ROMs> at iomem 0xd1000-0xd3fff,0xc9000-0xd0fff,0xc8000-0xc8fff,0xc0000-0xc7fff on isa0 fdc0: cannot reserve I/O port range (6 ports) sc0: <System console> on isa0 sc0: VGA <16 virtual consoles, flags=0x200> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 Timecounters tick every 10.000 msec IPsec: Initialized Security Association Processing. acpi_cpu: CPU throttling available, 16 steps from 100% to 6.2% ad0: 28629MB <ST330621A> [58168/16/63] at ata0-master UDMA100 ad1: 29312MB <Maxtor 33073H3> [59556/16/63] at ata0-slave UDMA100 acd0: CD-RW <PLEXTOR CD-R PX-W8432T> at ata1-master PIO4 ar0: 78533MB <ATA RAID0 array> [10011/255/63] status: READY subdisks: 0 READY ad2: 39266MB <IC35L040AVER07-0> [79780/16/63] at ata2-master UDMA100 1 READY ad3: 39266MB <IC35L040AVER07-0> [79780/16/63] at ata3-master UDMA100 Waiting 2 seconds for SCSI devices to settle Opened disk ad2 -> 16 Opened disk ad2 -> 16 Opened disk ad3 -> 16 Opened disk ad3 -> 16 Mounting root from ufs:/dev/ad0s1a fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xdc00-0xdc3f mem 0xdbe00000-0xdbefffff,0xdbfee000-0xdbfeefff irq 12 at device 7.0 on pci0 fxp0: Ethernet address 00:d0:b7:0e:a9:cb inphy0: <i82555 10/100 media interface> on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, autoReceived on Sat Apr 05 2003 - 11:47:54 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:37:02 UTC