-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 > > Grap the latest from ftp.deepcore.dk/pub/ATAng and apply the diff files > > to your src tree, remove the contents of sys/dev/ata and extract the > > ATAng-*tgz file there, then do the usual drill to get a new kernel... Tried to grab this last night, but got "550 conf-patch: Permission denied." when trying to retrieve conf-patch. > current driver from cvs doesn't find any disk -- when try to mount root > :( I'm also having a problem with the -current ata driver. I have an smp system with an offboard promise ide card, and when I build an smp kernel, the ide drives do not get detected. If I take smp out of the kernel though, the drives get detected fine. Anyone know why this might be? dmesg's are below as a unified diff between the non-smp kernel and the smp kernel. -Jason -------------------------------------------------------------------------- Freud himself was a bit of a cold fish, and one cannot avoid the suspicion that he was insufficiently fondled when he was an infant. -- Ashley Montagu - --- dmesg.up Sat Aug 9 01:38:11 2003 +++ dmesg.smp Fri Aug 8 05:11:04 2003 _at__at_ -1,99 +1,107 _at__at_ Copyright (c) 1992-2003 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. - -FreeBSD 5.1-CURRENT #0: Fri Aug 8 03:06:30 PDT 2003 +FreeBSD 5.1-CURRENT #1: Fri Aug 8 04:15:59 PDT 2003 root_at_moonchild.fantastica:/usr/obj/usr/src/sys/JKERN - -Preloaded elf kernel "/boot/kernel/kernel" at 0xc052c000. +Preloaded elf kernel "/boot/kernel/kernel" at 0xc0546000. Timecounter "i8254" frequency 1193182 Hz CPU: Pentium II/Pentium II Xeon/Celeron (350.80-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x652 Stepping = 2 Features=0x183fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR> real memory = 268435456 (256 MB) - -avail memory = 255090688 (243 MB) +avail memory = 254971904 (243 MB) +Programming 24 pins in IOAPIC #0 +IOAPIC #0 intpin 2 -> irq 0 +IOAPIC #0 intpin 16 -> irq 10 +IOAPIC #0 intpin 17 -> irq 11 +IOAPIC #0 intpin 19 -> irq 9 +FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs + cpu0 (BSP): apic id: 0, version: 0x00040011, at 0xfee00000 + cpu1 (AP): apic id: 1, version: 0x00040011, at 0xfee00000 + io0 (APIC): apic id: 2, version: 0x00170011, at 0xfec00000 Pentium Pro MTRR support enabled npx0: <math processor> on motherboard npx0: INT 16 interface pcibios: BIOS version 2.10 pcib0: <Intel 82443BX (440 BX) host to PCI bridge> at pcibus 0 on motherboard pci0: <PCI bus> on pcib0 pcib1: <PCI-PCI bridge> at device 1.0 on pci0 pci1: <PCI bus> on pcib1 pci1: <display, VGA> at device 0.0 (no driver attached) isab0: <PCI-ISA bridge> at device 7.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel PIIX4 UDMA33 controller> port 0xffa0-0xffaf at device 7.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xef40-0xef5f irq 9 at device 7.2 on pci0 usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uscanner0: Hewlett-Packard HP ScanJet 5200C, rev 1.00/1.00, addr 2 - -pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached) +piix0 port 0x440-0x44f at device 7.3 on pci0 +Timecounter "PIIX" frequency 3579545 Hz atapci1: <Promise PDC20262 UDMA66 controller> port 0xef00-0xef3f,0xefa8-0xefab,0xefa0-0xefa7,0xefac-0xefaf,0xefe0-0xefe7 mem 0xfebc0000-0xfebdffff irq 11 at device 13.0 on pci0 ata2: at 0xefe0 on atapci1 ata3: at 0xefa0 on atapci1 ahc0: <Adaptec 2940 Ultra SCSI adapter> port 0xe800-0xe8ff mem 0xfebff000-0xfebfffff irq 10 at device 15.0 on pci0 aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs pcm0: <Creative EMU10K1> port 0xef80-0xef9f irq 11 at device 16.0 on pci0 pcm0: <TriTech TR28602 AC97 Codec> dc0: <82c169 PNIC 10/100BaseTX> port 0xe400-0xe4ff mem 0xfebfef00-0xfebfefff irq 11 at device 18.0 on pci0 dc0: Ethernet address: 00:a0:cc:40:8e:3e miibus0: <MII bus> on dc0 bmtphy0: <BCM5201 10/100baseTX PHY> on miibus0 bmtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto pci0: <multimedia, video> at device 20.0 (no driver attached) pci0: <multimedia> at device 20.1 (no driver attached) orm0: <Option ROMs> at iomem 0xd0800-0xd1fff,0xcc000-0xd07ff,0xc0000-0xca7ff on isa0 atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model Generic PS/2 mouse, device ID 0 fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/9 bytes threshold ppbus0: <Parallel port bus> on ppc0 ppbus0: IEEE1284 device found /NIBBLE Probing for PnP devices on ppbus0: ppbus0: <Hewlett-Packard HP LaserJet 5L/0101.03> HP ENHANCED PCL5,PJL plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 unknown: <PNP0303> can't assign resources (port) unknown: <PNP0c02> can't assign resources (port) unknown: <PNP0501> can't assign resources (port) unknown: <PNP0501> can't assign resources (port) unknown: <PNP0401> can't assign resources (port) unknown: <PNP0700> can't assign resources (port) unknown: <PNP0f13> can't assign resources (irq) - -Timecounter "TSC" frequency 350797334 Hz +APIC_IO: Testing 8254 interrupt delivery +APIC_IO: routing 8254 via IOAPIC #0 intpin 2 +Timecounter "TSC" frequency 350796749 Hz Timecounters tick every 10.000 msec - -ad4: 57241MB <ST360021A> [116301/16/63] at ata2-master UDMA66 - -ad6: 25965MB <Maxtor 92720U8> [52755/16/63] at ata3-master UDMA66 +ata2-master: timeout waiting for interrupt +ata2-master: ATA identify failed +ata3-master: timeout waiting for interrupt +ata3-master: ATA identify failed acd0: CD-RW <CR-4804TE> at ata0-master PIO3 Waiting 5 seconds for SCSI devices to settle +SMP: AP CPU #1 Launched! da0 at ahc0 bus 0 target 2 lun 0 da0: <IBM DNES-309170W SAH0> Fixed Direct Access SCSI-3 device da0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit), Tagged Queueing Enabled da0: 8748MB (17916240 512 byte sectors: 255H 63S/T 1115C) Mounting root from ufs:/dev/da0s1a - -dc0: failed to force tx and rx to idle state - -dc0: failed to force tx and rx to idle state - -Accounting enabled - -cd0 at ahc0 bus 0 target 3 lun 0 - -cd0: <PLEXTOR CD-ROM PX-32TS 1.03> Removable CD-ROM SCSI-2 device - -cd0: 20.000MB/s transfers (20.000MHz, offset 15) - -cd0: Attempt to query device size failed: NOT READY, Medium not present -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.2.1 (FreeBSD) Comment: See https://private.idealab.com/public/jason/jason.gpg iD8DBQE/QW9AswXMWWtptckRAknOAKDp694qes5FUSOZsJXyICxXKE9eEgCgvyXy sNpWuOzekc3a2wEFBhnM56c= =LTUn -----END PGP SIGNATURE-----Received on Mon Aug 18 2003 - 15:28:49 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:37:19 UTC