Am 25.12.'03 schrieb Michael Lestinsky: > On 24.12.'03 M. Warner Losh wrote: > > You may try setting hw.cbb.start_memory as well. > > I did this and applied your patch as well. Both didn't change anything. > Do you want me to enable any debugging options? Oops, after fixing some typos in my /boot/loader.conf: | hw.pci.allow_unsupported_io_range=1 | hw.cbb.start_memory=0x88000000 | hw.cbb.debug=1 | hw.cardbus.debug=1 | hw.cardbus.cis_debug=1 Inserting the card for the first time (or booting with the card inserted): | [...] | cbb0: <RF5C476 PCI-CardBus Bridge> at device 3.0 on pci2 | start (88000000) < sc->membase (e0200000) | end (ffffffff) > sc->memlimit (e02fffff) | cbb0: PCI Memory allocated: 88000000 | cardbus0: <CardBus bus> on cbb0 | pccard0: <16-bit PCCard bus> on cbb0 | pcib1: slot 3 INTA is routed to irq 10 | cbb0: [MPSAFE] | cbb1: <RF5C476 PCI-CardBus Bridge> at device 3.1 on pci2 | start (88000000) < sc->membase (e0200000) | end (ffffffff) > sc->memlimit (e02fffff) | cbb1: PCI Memory allocated: 88001000 | cardbus1: <CardBus bus> on cbb1 | pccard1: <16-bit PCCard bus> on cbb1 | pcib1: slot 3 INTB is routed to irq 10 | cbb1: [MPSAFE] | [...] | Status is 0x30000006 | Status is 0x30000820 | cbb1: card inserted: event=0x00000000, state=30000820 | cbb1: cbb_power: 3V | cbb1: cbb_power: 0V | cbb1: CardBus card activation failed After one unplug-replug-cycle: | Status is 0x30000820 | cbb1: card inserted: event=0x00000000, state=30000820 | cbb1: cbb_power: 3V | start (88000000) < sc->membase (e0200000) | end (ffffffff) > sc->memlimit (e02fffff) | TUPLE: LINKTARGET [3]: 43 49 53 | Manufacturer ID: 71021200 | TUPLE: Unknown(0x04) [6]: 03 01 00 00 00 00 | TUPLE: Unknown(0x05) [14]: 41 b1 39 b5 1e 2d 4e 56 30 ff ff 02 e9 00 | cardbus1: Opening BAR: type=MEM, bar=10, len=10000 | CIS reading done | start (88000000) < sc->membase (e0200000) | end (ffffffff) > sc->memlimit (e02fffff) | cardbus1: Non-prefetchable memory at 88010000-8801ffff | ath0: <Atheros 5212> mem 0x88010000-0x8801ffff irq 10 at device 0.0 on cardbus1 | start (88010000) < sc->membase (e0200000) | ath0: mac 5.6 phy 4.1 5ghz radio 4.5 | ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps | ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps | ath0: 802.11 address: 00:09:5b:89:f9:37 Is there anything useful I could do in order to help debugging the problem? Thanks so far, Michael
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:37:36 UTC