I already posted this to stable, but got no answer. Hello, I built in a card which is identified as Dolphin 4036. This card has 4 serial ports (Sun Chip) and looking at the Dolphin Webpage there is a similiar product named FastPCI 4056. The card is recogniced and sio4 and sio5 are found and works correct. But there is no way to get sio6 and 7 (3rd/4th port on the card) working. Any hints how to add this card to pucdata would be very helpful. -- Best regards / Mit freundlichen Gruessen, Karl M. Joch ################ ## dmesg.boot ## FreeBSD 5.2.1-RELEASE-p6 #1: Fri Oct 29 12:19:20 CEST 2004 Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a50000. Preloaded elf module "/boot/kernel/splash_bmp.ko" at 0xc0a50244. Preloaded splash_image_data "/boot/cts.bmp" at 0xc0a502f4. Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Pentium(R) 4 CPU 2.80GHz (2788.69-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf29 Stepping = 9 Features=0xbfebf9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> real memory = 528482304 (504 MB) avail memory = 503685120 (480 MB) Pentium Pro MTRR support enabled npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface pcibios: BIOS version 2.10 Using $PIR table, 9 entries at 0xc00f78c0 pcib0: <Host to PCI bridge> at pcibus 0 on motherboard pci0: <PCI bus> on pcib0 pci_cfgintr: 0:9 INTA BIOS irq 10 pci_cfgintr: 0:11 INTA BIOS irq 11 pci_cfgintr: 0:13 INTA BIOS irq 5 pci_cfgintr: 0:15 INTA BIOS irq 5 pci_cfgintr: 0:17 INTA BIOS irq 5 agp0: <SIS Generic host to PCI bridge> mem 0xe0000000-0xe3ffffff at device 0.0 on pci0 pcib1: <PCI-PCI bridge> at device 1.0 on pci0 pci1: <PCI bus> on pcib1 pci1: <display, VGA> at device 0.0 (no driver attached) isab0: <PCI-ISA bridge> at device 2.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <SiS 962/963 UDMA133 controller> port 0xff00-0xff0f at device 2.5 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata0: [MPSAFE] ata1: at 0x170 irq 15 on atapci0 ata1: [MPSAFE] puc0: <Dolphin Peripherals 4036> port 0xd400-0xd40f,0xd800-0xd81f irq 10 at device 9.0 on pci0 sio4: <Dolphin Peripherals 4036> on puc0 sio4: type 16550A sio4: unable to activate interrupt in fast mode - using normal mode sio5: <Dolphin Peripherals 4036> on puc0 sio5: type 16550A sio5: unable to activate interrupt in fast mode - using normal mode ahc0: <Adaptec 2940 SCSI adapter> port 0xdc00-0xdcff mem 0xdfffb000-0xdfffbfff irq 11 at device 11.0 on pci0 aic7870: Single Channel A, SCSI Id=7, 16/253 SCBs rl0: <RealTek 8139 10/100BaseTX> port 0xd000-0xd0ff mem 0xdfffaf00-0xdfffafff irq 5 at device 13.0 on pci0 rl0: Ethernet address: 00:40:95:32:55:e7 miibus0: <MII bus> on rl0 rlphy0: <RealTek internal media interface> on miibus0 rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto rl1: <RealTek 8139 10/100BaseTX> port 0xcc00-0xccff mem 0xdfffae00-0xdfffaeff irq 5 at device 15.0 on pci0 rl1: Ethernet address: 00:40:95:30:b2:2d miibus1: <MII bus> on rl1 rlphy1: <RealTek internal media interface> on miibus1 rlphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto rl2: <RealTek 8139 10/100BaseTX> port 0xc800-0xc8ff mem 0xdfffad00-0xdfffadff irq 5 at device 17.0 on pci0 rl2: Ethernet address: 00:40:95:30:7e:33 miibus2: <MII bus> on rl2 rlphy2: <RealTek internal media interface> on miibus2 rlphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto orm0: <Option ROM> at iomem 0xc0000-0xcbfff on isa0 pmtimer0 on isa0 atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 ppc0: parallel port not found. sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 unknown: <PNP0303> can't assign resources (port) unknown: <PNP0501> can't assign resources (port) unknown: <PNP0700> can't assign resources (port) Timecounter "TSC" frequency 2788686564 Hz quality 800 Timecounters tick every 10.000 msec IPv6 packet filtering initialized, unlimited logging ipfw2 initialized, divert enabled, rule-based forwarding enabled, default to deny, logging unlimited IPsec: Initialized Security Association Processing. GEOM: create disk ad0 dp=0xc4747b60 ad0: 78533MB <ExcelStor Technology J680> [159560/16/63] at ata0-master UDMA100 GEOM: create disk ad1 dp=0xc46f4d60 ad1: 78533MB <ExcelStor Technology J680> [159560/16/63] at ata0-slave UDMA100 acd0: CDROM <LTN526> at ata1-slave PIO4 Waiting 15 seconds for SCSI devices to settle sa0 at ahc0 bus 0 target 1 lun 0 sa0: <COMPAQ SDT-10000 1.09> Removable Sequential Access SCSI-2 device sa0: 10.000MB/s transfers (10.000MHz, offset 15) Mounting root from ufs:/dev/ad0s1a module_register: module if_stf already exists! Module if_stf failed to register: 17 _______________________________________________ freebsd-stable_at_freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-stable To unsubscribe, send any mail to "freebsd-stable-unsubscribe_at_freebsd.org"Received on Sun Oct 31 2004 - 08:53:43 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:38:20 UTC