I have tried to reproduce this and cannot, can you tell me more details about this hardware, is it off-the-shelf or something non-production, etc etc. Did an install of a stock ICH9 system with this NIC, and have seen no such checksum failure, everything works fine :( Jack On Thu, Jul 9, 2009 at 11:35 AM, Jack Vogel <jfvogel_at_gmail.com> wrote: > I am looking into this, thanks for the report. > > Jack > > > > On Thu, Jul 9, 2009 at 10:52 AM, Chris Ruiz <yr.retarded_at_gmail.com> wrote: > >> On Thu, Jul 9, 2009 at 6:39 AM, Stanislav Sedov<stas_at_freebsd.org> wrote: >> > On Wed, 8 Jul 2009 22:58:27 -0500 >> > Chris Ruiz <yr.retarded_at_gmail.com> mentioned: >> > >> >> i just upgraded from r194562 to r195477 in order to test BETA1 and my >> >> e1000 adapter no longer attaching to the driver. >> >> >> >> pciconf -lv output >> >> >> >> em0_at_pci0:0:25:0: class=0x020000 card=0x00018086 chip=0x10bd8086 >> >> rev=0x02 hdr=0x00 >> >> vendor = 'Intel Corporation' >> >> device = 'Intel 82566DM Gigabit Ethernet Adapter (82566DM)' >> >> class = network >> >> subclass = ethernet >> >> >> >> here's a quick list of relevant commits since my last kernel build: >> >> r195409, r195168, r195049, r194979, r194925, r194911, r194865. >> >> >> > >> > Hi, Chris! >> > >> > Can you provide the verbose boot log? >> >> Turns out it's caused by the driver thinking the EEPROM checksum is >> invalid. Here's a verbose dmesg: >> >> Copyright (c) 1992-2009 The FreeBSD Project. >> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 >> The Regents of the University of California. All rights reserved. >> FreeBSD is a registered trademark of The FreeBSD Foundation. >> FreeBSD 8.0-BETA1 #0 r195483: Wed Jul 8 21:51:57 CDT 2009 >> root_at_attack.young-alumni.com:/usr/obj/usr/src/sys/FAILWHALE >> WARNING: WITNESS option enabled, expect reduced performance. >> Preloaded elf kernel "/boot/kernel/kernel" at 0xffffffff80dce000. >> Preloaded elf obj module "/boot/kernel/zfs.ko" at 0xffffffff80dce2b0. >> Preloaded elf obj module "/boot/kernel/opensolaris.ko" at >> 0xffffffff80dce958. >> Preloaded /boot/zfs/zpool.cache "/boot/zfs/zpool.cache" at >> 0xffffffff80dcef88. >> Timecounter "i8254" frequency 1193182 Hz quality 0 >> Calibrating TSC clock ... TSC clock: 3001458636 Hz >> CPU: Intel(R) Core(TM)2 Duo CPU E6850 _at_ 3.00GHz (3001.46-MHz K8-class >> CPU) >> Origin = "GenuineIntel" Id = 0x6fb Stepping = 11 >> >> Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> >> Features2=0xe3f5<SSE3,DTES64,DS_CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM> >> AMD Features=0x20100800<SYSCALL,NX,LM> >> AMD Features2=0x1<LAHF> >> TSC: P-state invariant >> real memory = 8589934592 (8192 MB) >> Physical memory chunk(s): >> 0x0000000000001000 - 0x0000000000040fff, 262144 bytes (64 pages) >> 0x0000000000051000 - 0x0000000000099fff, 299008 bytes (73 pages) >> 0x0000000000e01000 - 0x00000000cdbcbfff, 3437015040 bytes (839115 pages) >> 0x00000000cdc9a000 - 0x00000000ceec4fff, 19050496 bytes (4651 pages) >> 0x00000000ceec7000 - 0x00000000cef79fff, 733184 bytes (179 pages) >> 0x00000000cefe5000 - 0x00000000cefe5fff, 4096 bytes (1 pages) >> 0x00000000ceff2000 - 0x00000000ceff2fff, 4096 bytes (1 pages) >> 0x00000000cefff000 - 0x00000000ceffffff, 4096 bytes (1 pages) >> 0x0000000100000000 - 0x000000021cbf3fff, 4777263104 bytes (1166324 pages) >> avail memory = 8192516096 (7812 MB) >> ACPI APIC Table: <INTEL DQ3510J > >> INTR: Adding local APIC 1 as a target >> FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs >> FreeBSD/SMP: 1 package(s) x 2 core(s) >> cpu0 (BSP): APIC ID: 0 >> cpu1 (AP): APIC ID: 1 >> APIC: CPU 0 has ACPI ID 1 >> APIC: CPU 1 has ACPI ID 2 >> ULE: setup cpu 0 >> ULE: setup cpu 1 >> This module (opensolaris) contains code covered by the >> Common Development and Distribution License (CDDL) >> see http://opensolaris.org/os/licensing/opensolaris_license/ >> ACPI: RSDP 0xfe020 00014 (v0 INTEL ) >> ACPI: RSDT 0xceffd038 00070 (v1 INTEL DQ3510J 000003BA 01000013) >> ACPI: FACP 0xceffc000 00074 (v1 INTEL DQ3510J 000003BA MSFT 01000013) >> ACPI: DSDT 0xceff8000 03D6A (v1 INTEL DQ3510J 000003BA MSFT 01000013) >> ACPI: FACS 0xcef87000 00040 >> ACPI: APIC 0xceff7000 00078 (v1 INTEL DQ3510J 000003BA MSFT 01000013) >> ACPI: WDDT 0xceff6000 00040 (v1 INTEL DQ3510J 000003BA MSFT 01000013) >> ACPI: MCFG 0xceff5000 0003C (v1 INTEL DQ3510J 000003BA MSFT 01000013) >> ACPI: ASF! 0xceff4000 000A6 (v32 INTEL DQ3510J 000003BA MSFT 01000013) >> ACPI: HPET 0xceff3000 00038 (v1 INTEL DQ3510J 000003BA MSFT 01000013) >> ACPI: DMAR 0xceff1000 000F8 (v1 INTEL DQ3510J 000003BA MSFT 01000013) >> ACPI: ASPT 0xceff0000 0002C (v3 INTEL DQ3510J 000003BA MSFT 01000013) >> ACPI: WDTT 0xcefef000 002CC (v1 INTEL DQ3510J 000003BA MSFT 01000013) >> ACPI: SSDT 0xcefee000 00204 (v1 INTEL CpuPm 000003BA MSFT 01000013) >> ACPI: SSDT 0xcefed000 001F9 (v1 INTEL Cpu0Ist 000003BA MSFT 01000013) >> ACPI: SSDT 0xcefec000 001F9 (v1 INTEL Cpu1Ist 000003BA MSFT 01000013) >> ACPI: SSDT 0xcefeb000 001F9 (v1 INTEL Cpu2Ist 000003BA MSFT 01000013) >> ACPI: SSDT 0xcefea000 001F9 (v1 INTEL Cpu3Ist 000003BA MSFT 01000013) >> ACPI: SSDT 0xcefe9000 000DD (v1 INTEL Cpu0Cst 000003BA MSFT 01000013) >> ACPI: SSDT 0xcefe8000 000DD (v1 INTEL Cpu1Cst 000003BA MSFT 01000013) >> ACPI: SSDT 0xcefe7000 000DD (v1 INTEL Cpu2Cst 000003BA MSFT 01000013) >> ACPI: SSDT 0xcefe6000 000DD (v1 INTEL Cpu3Cst 000003BA MSFT 01000013) >> ACPI: TCPA 0xcef7b000 00032 (v2 INTEL TIANO 00000002 MSFT 01000013) >> MADT: Found IO APIC ID 2, Interrupt 0 at 0xfec00000 >> ioapic0: Changing APIC ID to 2 >> ioapic0: Routing external 8259A's -> intpin 0 >> MADT: Interrupt override: source 0, irq 2 >> ioapic0: Routing IRQ 0 -> intpin 2 >> MADT: Interrupt override: source 9, irq 9 >> ioapic0: intpin 9 trigger: level >> lapic0: Routing NMI -> LINT1 >> lapic0: LINT1 trigger: edge >> lapic0: LINT1 polarity: high >> lapic1: Routing NMI -> LINT1 >> lapic1: LINT1 trigger: edge >> lapic1: LINT1 polarity: high >> ioapic0 <Version 2.0> irqs 0-23 on motherboard >> cpu0 BSP: >> ID: 0x00000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff >> lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff >> timer: 0x000100ef therm: 0x00010000 err: 0x00010000 pcm: 0x00000400 >> wlan: <802.11 Link Layer> >> ichwd module loaded >> io: <I/O> >> kbd0 at kbdmux0 >> mem: <memory> >> nfslock: pseudo-device >> null: <null device, zero device> >> random: <entropy source, Software, Yarrow> >> acpi0: <INTEL DQ3510J> on motherboard >> ioapic0: routing intpin 9 (ISA IRQ 9) to lapic 0 vector 48 >> acpi0: [MPSAFE] >> acpi0: [ITHREAD] >> acpi0: Power Button (fixed) >> acpi0: wakeup code va 0xffffff8000011000 pa 0x4000 >> acpi_bus_number: root bus has no _BBN, assuming 0 >> AcpiOsDerivePciId: \\_SB_.PCI0.TMEM -> bus 0 dev 0 func 0 >> acpi_bus_number: root bus has no _BBN, assuming 0 >> AcpiOsDerivePciId: \\_SB_.PCI0.PAMX -> bus 0 dev 0 func 0 >> acpi_bus_number: root bus has no _BBN, assuming 0 >> AcpiOsDerivePciId: \\_SB_.PCI0.LPC_.PRR0 -> bus 0 dev 31 func 0 >> acpi_bus_number: root bus has no _BBN, assuming 0 >> AcpiOsDerivePciId: \\_SB_.PCI0.LPC_.PRR1 -> bus 0 dev 31 func 0 >> acpi_bus_number: root bus has no _BBN, assuming 0 >> AcpiOsDerivePciId: \\_SB_.PCI0.LPC_.IELK.ELR0 -> bus 0 dev 0 func 0 >> ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10 >> Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 >> acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0 >> pci_link0: Index IRQ Rtd Ref IRQs >> Initial Probe 0 11 N 0 3 4 5 7 9 10 11 12 >> Validation 0 11 N 0 3 4 5 7 9 10 11 12 >> After Disable 0 255 N 0 3 4 5 7 9 10 11 12 >> pci_link1: Index IRQ Rtd Ref IRQs >> Initial Probe 0 10 N 0 3 4 5 7 9 10 11 12 >> Validation 0 10 N 0 3 4 5 7 9 10 11 12 >> After Disable 0 255 N 0 3 4 5 7 9 10 11 12 >> pci_link2: Index IRQ Rtd Ref IRQs >> Initial Probe 0 9 N 0 3 4 5 7 9 10 11 12 >> Validation 0 9 N 0 3 4 5 7 9 10 11 12 >> After Disable 0 255 N 0 3 4 5 7 9 10 11 12 >> pci_link3: Index IRQ Rtd Ref IRQs >> Initial Probe 0 11 N 0 3 4 5 7 9 10 11 12 >> Validation 0 11 N 0 3 4 5 7 9 10 11 12 >> After Disable 0 255 N 0 3 4 5 7 9 10 11 12 >> pci_link4: Index IRQ Rtd Ref IRQs >> Initial Probe 0 11 N 0 3 4 5 7 9 10 11 12 >> Validation 0 11 N 0 3 4 5 7 9 10 11 12 >> After Disable 0 255 N 0 3 4 5 7 9 10 11 12 >> pci_link5: Index IRQ Rtd Ref IRQs >> Initial Probe 0 9 N 0 3 4 5 7 9 10 11 12 >> Validation 0 9 N 0 3 4 5 7 9 10 11 12 >> After Disable 0 255 N 0 3 4 5 7 9 10 11 12 >> pci_link6: Index IRQ Rtd Ref IRQs >> Initial Probe 0 10 N 0 3 4 5 7 9 10 11 12 >> Validation 0 10 N 0 3 4 5 7 9 10 11 12 >> After Disable 0 255 N 0 3 4 5 7 9 10 11 12 >> pci_link7: Index IRQ Rtd Ref IRQs >> Initial Probe 0 11 N 0 3 4 5 7 9 10 11 12 >> Validation 0 11 N 0 3 4 5 7 9 10 11 12 >> After Disable 0 255 N 0 3 4 5 7 9 10 11 12 >> acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on >> acpi0 >> acpi_hpet0: vend: 0x8086 rev: 0x1 num: 3 hz: 14318180 opts: legacy_route >> 64-bit >> Timecounter "HPET" frequency 14318180 Hz quality 900 >> acpi_button0: <Sleep Button> on acpi0 >> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 >> pci0: <ACPI PCI bus> on pcib0 >> pci0: domain=0, physical bus=0 >> found-> vendor=0x8086, dev=0x29b0, revid=0x02 >> domain=0, bus=0, slot=0, func=0 >> class=06-00-00, hdrtype=0x00, mfdev=0 >> cmdreg=0x0006, statreg=0x2090, cachelnsz=0 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> found-> vendor=0x8086, dev=0x29b2, revid=0x02 >> domain=0, bus=0, slot=2, func=0 >> class=03-00-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0007, statreg=0x0090, cachelnsz=0 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> intpin=a, irq=11 >> powerspec 2 supports D0 D3 current D0 >> MSI supports 1 message >> map[10]: type Memory, range 32, base 0xe0380000, size 19, enabled >> map[14]: type I/O Port, range 32, base 0x2458, size 3, enabled >> map[18]: type Prefetchable Memory, range 32, base 0xd0000000, size >> 28, enabled >> map[1c]: type Memory, range 32, base 0xe0200000, size 20, enabled >> pcib0: matched entry for 0.2.INTA >> pcib0: slot 2 INTA hardwired to IRQ 16 >> found-> vendor=0x8086, dev=0x29b3, revid=0x02 >> domain=0, bus=0, slot=2, func=1 >> class=03-80-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0007, statreg=0x0090, cachelnsz=0 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> powerspec 2 supports D0 D3 current D0 >> map[10]: type Memory, range 32, base 0xe0300000, size 19, enabled >> found-> vendor=0x8086, dev=0x29b4, revid=0x02 >> domain=0, bus=0, slot=3, func=0 >> class=07-80-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0006, statreg=0x0018, cachelnsz=0 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> intpin=a, irq=11 >> powerspec 3 supports D0 D3 current D0 >> MSI supports 1 message, 64 bit >> map[10]: type Memory, range 64, base 0xe0427100, size 4, enabled >> pcib0: matched entry for 0.3.INTA >> pcib0: slot 3 INTA hardwired to IRQ 16 >> found-> vendor=0x8086, dev=0x29b6, revid=0x02 >> domain=0, bus=0, slot=3, func=2 >> class=01-01-85, hdrtype=0x00, mfdev=0 >> cmdreg=0x0005, statreg=0x00b0, cachelnsz=0 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> intpin=c, irq=9 >> powerspec 3 supports D0 D3 current D0 >> MSI supports 1 message, 64 bit >> map[10]: type I/O Port, range 32, base 0x2450, size 3, enabled >> map[14]: type I/O Port, range 32, base 0x246c, size 2, enabled >> map[18]: type I/O Port, range 32, base 0x2448, size 3, enabled >> map[1c]: type I/O Port, range 32, base 0x2468, size 2, enabled >> map[20]: type I/O Port, range 32, base 0x2420, size 4, enabled >> pcib0: matched entry for 0.3.INTC >> pcib0: slot 3 INTC hardwired to IRQ 18 >> found-> vendor=0x8086, dev=0x29b7, revid=0x02 >> domain=0, bus=0, slot=3, func=3 >> class=07-00-02, hdrtype=0x00, mfdev=0 >> cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> intpin=b, irq=10 >> powerspec 3 supports D0 D3 current D0 >> MSI supports 1 message, 64 bit >> map[10]: type I/O Port, range 32, base 0x2440, size 3, enabled >> map[14]: type Memory, range 32, base 0xe0425000, size 12, enabled >> pcib0: matched entry for 0.3.INTB >> pcib0: slot 3 INTB hardwired to IRQ 17 >> found-> vendor=0x8086, dev=0x10bd, revid=0x02 >> domain=0, bus=0, slot=25, func=0 >> class=02-00-00, hdrtype=0x00, mfdev=0 >> cmdreg=0x0007, statreg=0x0010, cachelnsz=0 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> intpin=a, irq=11 >> powerspec 2 supports D0 D3 current D0 >> MSI supports 1 message, 64 bit >> map[10]: type Memory, range 32, base 0xe0400000, size 17, enabled >> map[14]: type Memory, range 32, base 0xe0424000, size 12, enabled >> map[18]: type I/O Port, range 32, base 0x2400, size 5, enabled >> pcib0: matched entry for 0.25.INTA >> pcib0: slot 25 INTA hardwired to IRQ 20 >> found-> vendor=0x8086, dev=0x2937, revid=0x02 >> domain=0, bus=0, slot=26, func=0 >> class=0c-03-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> intpin=a, irq=9 >> map[20]: type I/O Port, range 32, base 0x20e0, size 5, enabled >> pcib0: matched entry for 0.26.INTA >> pcib0: slot 26 INTA hardwired to IRQ 18 >> found-> vendor=0x8086, dev=0x2938, revid=0x02 >> domain=0, bus=0, slot=26, func=1 >> class=0c-03-00, hdrtype=0x00, mfdev=0 >> cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> intpin=b, irq=9 >> map[20]: type I/O Port, range 32, base 0x20c0, size 5, enabled >> pcib0: matched entry for 0.26.INTB >> pcib0: slot 26 INTB hardwired to IRQ 21 >> found-> vendor=0x8086, dev=0x2939, revid=0x02 >> domain=0, bus=0, slot=26, func=2 >> class=0c-03-00, hdrtype=0x00, mfdev=0 >> cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> intpin=c, irq=10 >> map[20]: type I/O Port, range 32, base 0x20a0, size 5, enabled >> pcib0: matched entry for 0.26.INTC >> pcib0: slot 26 INTC hardwired to IRQ 17 >> found-> vendor=0x8086, dev=0x293c, revid=0x02 >> domain=0, bus=0, slot=26, func=7 >> class=0c-03-20, hdrtype=0x00, mfdev=0 >> cmdreg=0x0006, statreg=0x0290, cachelnsz=0 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> intpin=c, irq=10 >> powerspec 2 supports D0 D3 current D0 >> map[10]: type Memory, range 32, base 0xe0426c00, size 10, enabled >> pcib0: matched entry for 0.26.INTC >> pcib0: slot 26 INTC hardwired to IRQ 17 >> found-> vendor=0x8086, dev=0x293e, revid=0x02 >> domain=0, bus=0, slot=27, func=0 >> class=04-03-00, hdrtype=0x00, mfdev=0 >> cmdreg=0x0006, statreg=0x0010, cachelnsz=16 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> intpin=a, irq=10 >> powerspec 2 supports D0 D3 current D0 >> MSI supports 1 message, 64 bit >> map[10]: type Memory, range 64, base 0xe0420000, size 14, enabled >> pcib0: matched entry for 0.27.INTA >> pcib0: slot 27 INTA hardwired to IRQ 22 >> found-> vendor=0x8086, dev=0x2940, revid=0x02 >> domain=0, bus=0, slot=28, func=0 >> class=06-04-00, hdrtype=0x01, mfdev=1 >> cmdreg=0x0000, statreg=0x0010, cachelnsz=16 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) >> intpin=a, irq=255 >> powerspec 2 supports D0 D3 current D0 >> MSI supports 1 message >> found-> vendor=0x8086, dev=0x2942, revid=0x02 >> domain=0, bus=0, slot=28, func=1 >> class=06-04-00, hdrtype=0x01, mfdev=1 >> cmdreg=0x0000, statreg=0x0010, cachelnsz=16 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) >> intpin=b, irq=255 >> powerspec 2 supports D0 D3 current D0 >> MSI supports 1 message >> found-> vendor=0x8086, dev=0x2944, revid=0x02 >> domain=0, bus=0, slot=28, func=2 >> class=06-04-00, hdrtype=0x01, mfdev=1 >> cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) >> intpin=c, irq=255 >> powerspec 2 supports D0 D3 current D0 >> MSI supports 1 message >> found-> vendor=0x8086, dev=0x2946, revid=0x02 >> domain=0, bus=0, slot=28, func=3 >> class=06-04-00, hdrtype=0x01, mfdev=1 >> cmdreg=0x0000, statreg=0x0010, cachelnsz=16 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) >> intpin=d, irq=255 >> powerspec 2 supports D0 D3 current D0 >> MSI supports 1 message >> found-> vendor=0x8086, dev=0x2948, revid=0x02 >> domain=0, bus=0, slot=28, func=4 >> class=06-04-00, hdrtype=0x01, mfdev=1 >> cmdreg=0x0000, statreg=0x0010, cachelnsz=16 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) >> intpin=a, irq=255 >> powerspec 2 supports D0 D3 current D0 >> MSI supports 1 message >> found-> vendor=0x8086, dev=0x2934, revid=0x02 >> domain=0, bus=0, slot=29, func=0 >> class=0c-03-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> intpin=a, irq=11 >> map[20]: type I/O Port, range 32, base 0x2080, size 5, enabled >> pcib0: matched entry for 0.29.INTA >> pcib0: slot 29 INTA hardwired to IRQ 23 >> found-> vendor=0x8086, dev=0x2935, revid=0x02 >> domain=0, bus=0, slot=29, func=1 >> class=0c-03-00, hdrtype=0x00, mfdev=0 >> cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> intpin=b, irq=11 >> map[20]: type I/O Port, range 32, base 0x2060, size 5, enabled >> pcib0: matched entry for 0.29.INTB >> pcib0: slot 29 INTB hardwired to IRQ 19 >> found-> vendor=0x8086, dev=0x2936, revid=0x02 >> domain=0, bus=0, slot=29, func=2 >> class=0c-03-00, hdrtype=0x00, mfdev=0 >> cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> intpin=c, irq=9 >> map[20]: type I/O Port, range 32, base 0x2040, size 5, enabled >> pcib0: matched entry for 0.29.INTC >> pcib0: slot 29 INTC hardwired to IRQ 18 >> found-> vendor=0x8086, dev=0x293a, revid=0x02 >> domain=0, bus=0, slot=29, func=7 >> class=0c-03-20, hdrtype=0x00, mfdev=0 >> cmdreg=0x0006, statreg=0x0290, cachelnsz=0 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> intpin=a, irq=11 >> powerspec 2 supports D0 D3 current D0 >> map[10]: type Memory, range 32, base 0xe0426800, size 10, enabled >> pcib0: matched entry for 0.29.INTA >> pcib0: slot 29 INTA hardwired to IRQ 23 >> found-> vendor=0x8086, dev=0x244e, revid=0x92 >> domain=0, bus=0, slot=30, func=0 >> class=06-04-01, hdrtype=0x01, mfdev=0 >> cmdreg=0x0107, statreg=0x0010, cachelnsz=0 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) >> found-> vendor=0x8086, dev=0x2914, revid=0x02 >> domain=0, bus=0, slot=31, func=0 >> class=06-01-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0107, statreg=0x0210, cachelnsz=0 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> found-> vendor=0x8086, dev=0x2922, revid=0x02 >> domain=0, bus=0, slot=31, func=2 >> class=01-06-01, hdrtype=0x00, mfdev=0 >> cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> intpin=a, irq=9 >> powerspec 3 supports D0 D3 current D0 >> MSI supports 16 messages >> map[10]: type I/O Port, range 32, base 0x2438, size 3, enabled >> map[14]: type I/O Port, range 32, base 0x2464, size 2, enabled >> map[18]: type I/O Port, range 32, base 0x2430, size 3, enabled >> map[1c]: type I/O Port, range 32, base 0x2460, size 2, enabled >> map[20]: type I/O Port, range 32, base 0x2020, size 5, enabled >> map[24]: type Memory, range 32, base 0xe0426000, size 11, enabled >> pcib0: matched entry for 0.31.INTA >> pcib0: slot 31 INTA hardwired to IRQ 21 >> found-> vendor=0x8086, dev=0x2930, revid=0x02 >> domain=0, bus=0, slot=31, func=3 >> class=0c-05-00, hdrtype=0x00, mfdev=0 >> cmdreg=0x0003, statreg=0x0280, cachelnsz=0 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> intpin=b, irq=9 >> map[10]: type Memory, range 64, base 0xe0427000, size 8, enabled >> map[20]: type I/O Port, range 32, base 0x2000, size 5, enabled >> pcib0: matched entry for 0.31.INTB >> pcib0: slot 31 INTB hardwired to IRQ 18 >> vgapci0: <VGA-compatible display> port 0x2458-0x245f mem >> 0xe0380000-0xe03fffff,0xd0000000-0xdfffffff,0xe0200000-0xe02fffff irq >> 16 at device 2.0 on pci0 >> agp0: <Intel Q35 SVGA controller> on vgapci0 >> vgapci0: Reserved 0x10000000 bytes for rid 0x18 type 3 at 0xd0000000 >> vgapci0: Reserved 0x80000 bytes for rid 0x10 type 3 at 0xe0380000 >> vgapci0: Reserved 0x100000 bytes for rid 0x1c type 3 at 0xe0200000 >> agp0: detected 6140k stolen memory >> agp0: aperture size is 256M >> vgapci1: <VGA-compatible display> mem 0xe0300000-0xe037ffff at device >> 2.1 on pci0 >> pci0: <simple comms> at device 3.0 (no driver attached) >> atapci0: <Intel ATA controller> port >> 0x2450-0x2457,0x246c-0x246f,0x2448-0x244f,0x2468-0x246b,0x2420-0x242f >> irq 18 at device 3.2 on pci0 >> atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x2420 >> ioapic0: routing intpin 18 (PCI IRQ 18) to lapic 0 vector 49 >> atapci0: [MPSAFE] >> atapci0: [ITHREAD] >> ata2: <ATA channel 0> on atapci0 >> atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x2450 >> atapci0: Reserved 0x4 bytes for rid 0x14 type 4 at 0x246c >> ata2: reset tp1 mask=03 ostat0=7f ostat1=7f >> ata2: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f >> ata2: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f >> ata2: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f >> ata2: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f >> ata2: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f >> ata2: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f >> ata2: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f >> ata2: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f >> ata2: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f >> ata2: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f >> ata2: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f >> ata2: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f >> ata2: stat1=0x7f err=0x7f lsb=0x7f msb=0x7f >> ata2: reset tp2 stat0=ff stat1=ff devices=0x0 >> ata2: [MPSAFE] >> ata2: [ITHREAD] >> ata3: <ATA channel 1> on atapci0 >> atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x2448 >> atapci0: Reserved 0x4 bytes for rid 0x1c type 4 at 0x2468 >> ata3: reset tp1 mask=03 ostat0=7f ostat1=7f >> ata3: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f >> ata3: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f >> ata3: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f >> ata3: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f >> ata3: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f >> ata3: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f >> ata3: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f >> ata3: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f >> ata3: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f >> ata3: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f >> ata3: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f >> ata3: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f >> ata3: stat1=0x7f err=0x7f lsb=0x7f msb=0x7f >> ata3: reset tp2 stat0=ff stat1=ff devices=0x0 >> ata3: [MPSAFE] >> ata3: [ITHREAD] >> pci0: <simple comms, UART> at device 3.3 (no driver attached) >> em0: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0x2400-0x241f >> mem 0xe0400000-0xe041ffff,0xe0424000-0xe0424fff irq 20 at device 25.0 >> on pci0 >> em0: Reserved 0x20000 bytes for rid 0x10 type 3 at 0xe0400000 >> em0: attempting to allocate 1 MSI vectors (1 supported) >> msi: routing MSI IRQ 256 to local APIC 0 vector 50 >> em0: using IRQ 256 for MSI >> em0: Using MSI interrupt >> em0: Reserved 0x1000 bytes for rid 0x14 type 3 at 0xe0424000 >> em0: The EEPROM Checksum Is Not Valid >> device_attach: em0 attach returned 5 >> uhci0: <Intel 82801I (ICH9) USB controller> port 0x20e0-0x20ff irq 18 >> at device 26.0 on pci0 >> uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0x20e0 >> uhci0: [MPSAFE] >> uhci0: [ITHREAD] >> uhci0: LegSup = 0x0f10 >> usbus0: <Intel 82801I (ICH9) USB controller> on uhci0 >> uhci1: <Intel 82801I (ICH9) USB controller> port 0x20c0-0x20df irq 21 >> at device 26.1 on pci0 >> uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0x20c0 >> ioapic0: routing intpin 21 (PCI IRQ 21) to lapic 0 vector 50 >> uhci1: [MPSAFE] >> uhci1: [ITHREAD] >> uhci1: LegSup = 0x0f10 >> usbus1: <Intel 82801I (ICH9) USB controller> on uhci1 >> uhci2: <Intel 82801I (ICH9) USB controller> port 0x20a0-0x20bf irq 17 >> at device 26.2 on pci0 >> uhci2: Reserved 0x20 bytes for rid 0x20 type 4 at 0x20a0 >> ioapic0: routing intpin 17 (PCI IRQ 17) to lapic 0 vector 51 >> uhci2: [MPSAFE] >> uhci2: [ITHREAD] >> uhci2: LegSup = 0x0f10 >> usbus2: <Intel 82801I (ICH9) USB controller> on uhci2 >> ehci0: <Intel 82801I (ICH9) USB 2.0 controller> mem >> 0xe0426c00-0xe0426fff irq 17 at device 26.7 on pci0 >> ehci0: Reserved 0x400 bytes for rid 0x10 type 3 at 0xe0426c00 >> ehci0: [MPSAFE] >> ehci0: [ITHREAD] >> usbus3: EHCI version 1.0 >> usbus3: <Intel 82801I (ICH9) USB 2.0 controller> on ehci0 >> pci0: <multimedia, HDA> at device 27.0 (no driver attached) >> pcib1: <ACPI PCI-PCI bridge> at device 28.0 on pci0 >> pcib1: domain 0 >> pcib1: secondary bus 1 >> pcib1: subordinate bus 1 >> pcib1: I/O decode 0x0-0x0 >> pcib1: no prefetched decode >> pci1: <ACPI PCI bus> on pcib1 >> pci1: domain=0, physical bus=1 >> pcib2: <ACPI PCI-PCI bridge> at device 28.1 on pci0 >> pcib2: domain 0 >> pcib2: secondary bus 2 >> pcib2: subordinate bus 2 >> pcib2: I/O decode 0x0-0x0 >> pcib2: no prefetched decode >> pci2: <ACPI PCI bus> on pcib2 >> pci2: domain=0, physical bus=2 >> pcib3: <ACPI PCI-PCI bridge> at device 28.2 on pci0 >> pcib3: domain 0 >> pcib3: secondary bus 3 >> pcib3: subordinate bus 3 >> pcib3: I/O decode 0x1000-0x1fff >> pcib3: memory decode 0xe0100000-0xe01fffff >> pcib3: no prefetched decode >> pci3: <ACPI PCI bus> on pcib3 >> pci3: domain=0, physical bus=3 >> found-> vendor=0x11ab, dev=0x6101, revid=0xb1 >> domain=0, bus=3, slot=0, func=0 >> class=01-01-8f, hdrtype=0x00, mfdev=0 >> cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> intpin=a, irq=9 >> powerspec 2 supports D0 D1 D3 current D0 >> MSI supports 1 message >> map[10]: type I/O Port, range 32, base 0x1018, size 3, enabled >> pcib3: requested I/O range 0x1018-0x101f: in range >> map[14]: type I/O Port, range 32, base 0x1024, size 2, enabled >> pcib3: requested I/O range 0x1024-0x1027: in range >> map[18]: type I/O Port, range 32, base 0x1010, size 3, enabled >> pcib3: requested I/O range 0x1010-0x1017: in range >> map[1c]: type I/O Port, range 32, base 0x1020, size 2, enabled >> pcib3: requested I/O range 0x1020-0x1023: in range >> map[20]: type I/O Port, range 32, base 0x1000, size 4, enabled >> pcib3: requested I/O range 0x1000-0x100f: in range >> map[24]: type Memory, range 32, base 0xe0100000, size 9, enabled >> pcib3: requested memory range 0xe0100000-0xe01001ff: good >> pcib3: matched entry for 3.0.INTA >> pcib3: slot 0 INTA hardwired to IRQ 18 >> atapci1: <Marvell 88SX6101 UDMA133 controller> port >> 0x1018-0x101f,0x1024-0x1027,0x1010-0x1017,0x1020-0x1023,0x1000-0x100f >> mem 0xe0100000-0xe01001ff irq 18 at device 0.0 on pci3 >> atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0x1000 >> atapci1: [MPSAFE] >> atapci1: [ITHREAD] >> ata4: <ATA channel 0> on atapci1 >> atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1018 >> atapci1: Reserved 0x4 bytes for rid 0x14 type 4 at 0x1024 >> ata4: reset tp1 mask=03 ostat0=50 ostat1=51 >> ata4: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb >> ata4: stat1=0x10 err=0x01 lsb=0x14 msb=0xeb >> ata4: reset tp2 stat0=00 stat1=10 devices=0x30000 >> ata4: [MPSAFE] >> ata4: [ITHREAD] >> pcib4: <ACPI PCI-PCI bridge> at device 28.3 on pci0 >> pcib4: domain 0 >> pcib4: secondary bus 4 >> pcib4: subordinate bus 4 >> pcib4: I/O decode 0x0-0x0 >> pcib4: no prefetched decode >> pci4: <ACPI PCI bus> on pcib4 >> pci4: domain=0, physical bus=4 >> pcib5: <ACPI PCI-PCI bridge> at device 28.4 on pci0 >> pcib5: domain 0 >> pcib5: secondary bus 5 >> pcib5: subordinate bus 5 >> pcib5: I/O decode 0x0-0x0 >> pcib5: no prefetched decode >> pci5: <ACPI PCI bus> on pcib5 >> pci5: domain=0, physical bus=5 >> uhci3: <Intel 82801I (ICH9) USB controller> port 0x2080-0x209f irq 23 >> at device 29.0 on pci0 >> uhci3: Reserved 0x20 bytes for rid 0x20 type 4 at 0x2080 >> ioapic0: routing intpin 23 (PCI IRQ 23) to lapic 0 vector 52 >> uhci3: [MPSAFE] >> uhci3: [ITHREAD] >> uhci3: LegSup = 0x0f10 >> usbus4: <Intel 82801I (ICH9) USB controller> on uhci3 >> uhci4: <Intel 82801I (ICH9) USB controller> port 0x2060-0x207f irq 19 >> at device 29.1 on pci0 >> uhci4: Reserved 0x20 bytes for rid 0x20 type 4 at 0x2060 >> ioapic0: routing intpin 19 (PCI IRQ 19) to lapic 0 vector 53 >> uhci4: [MPSAFE] >> uhci4: [ITHREAD] >> uhci4: LegSup = 0x0f10 >> usbus5: <Intel 82801I (ICH9) USB controller> on uhci4 >> uhci5: <Intel 82801I (ICH9) USB controller> port 0x2040-0x205f irq 18 >> at device 29.2 on pci0 >> uhci5: Reserved 0x20 bytes for rid 0x20 type 4 at 0x2040 >> uhci5: [MPSAFE] >> uhci5: [ITHREAD] >> uhci5: LegSup = 0x0f10 >> usbus6: <Intel 82801I (ICH9) USB controller> on uhci5 >> ehci1: <Intel 82801I (ICH9) USB 2.0 controller> mem >> 0xe0426800-0xe0426bff irq 23 at device 29.7 on pci0 >> ehci1: Reserved 0x400 bytes for rid 0x10 type 3 at 0xe0426800 >> ehci1: [MPSAFE] >> ehci1: [ITHREAD] >> usbus7: EHCI version 1.0 >> usbus7: <Intel 82801I (ICH9) USB 2.0 controller> on ehci1 >> pcib6: <ACPI PCI-PCI bridge> at device 30.0 on pci0 >> pcib6: domain 0 >> pcib6: secondary bus 6 >> pcib6: subordinate bus 6 >> pcib6: I/O decode 0xf000-0xfff >> pcib6: memory decode 0xe0000000-0xe00fffff >> pcib6: no prefetched decode >> pcib6: Subtractively decoded bridge. >> pci6: <ACPI PCI bus> on pcib6 >> pci6: domain=0, physical bus=6 >> found-> vendor=0x168c, dev=0x0013, revid=0x01 >> domain=0, bus=6, slot=0, func=0 >> class=02-00-00, hdrtype=0x00, mfdev=0 >> cmdreg=0x0216, statreg=0x0290, cachelnsz=16 (dwords) >> lattimer=0x20 (960 ns), mingnt=0x0a (2500 ns), maxlat=0x1c (7000 >> ns) >> intpin=a, irq=9 >> powerspec 2 supports D0 D3 current D0 >> map[10]: type Memory, range 32, base 0xe0000000, size 16, enabled >> pcib6: requested memory range 0xe0000000-0xe000ffff: good >> pcib6: matched entry for 6.0.INTA >> pcib6: slot 0 INTA hardwired to IRQ 21 >> found-> vendor=0x11c1, dev=0x5811, revid=0x70 >> domain=0, bus=6, slot=3, func=0 >> class=0c-00-10, hdrtype=0x00, mfdev=0 >> cmdreg=0x0216, statreg=0x0290, cachelnsz=16 (dwords) >> lattimer=0x20 (960 ns), mingnt=0x0c (3000 ns), maxlat=0x18 (6000 >> ns) >> intpin=a, irq=11 >> powerspec 2 supports D0 D1 D2 D3 current D0 >> map[10]: type Memory, range 32, base 0xe0010000, size 12, enabled >> pcib6: requested memory range 0xe0010000-0xe0010fff: good >> pcib6: matched entry for 6.3.INTA >> pcib6: slot 3 INTA hardwired to IRQ 19 >> ath0: <Atheros 5212> mem 0xe0000000-0xe000ffff irq 21 at device 0.0 on >> pci6 >> ath0: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xe0000000 >> ath0: [MPSAFE] >> ath0: [ITHREAD] >> ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps >> ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps >> 24Mbps 36Mbps 48Mbps 54Mbps >> ath0: turboG rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps >> 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps >> ath0: AR2413 mac 7.9 RF2413 phy 4.5 >> ath0: Use hw queue 1 for WME_AC_BE traffic >> ath0: Use hw queue 0 for WME_AC_BK traffic >> ath0: Use hw queue 2 for WME_AC_VI traffic >> ath0: Use hw queue 3 for WME_AC_VO traffic >> ath0: Use hw queue 8 for CAB traffic >> ath0: Use hw queue 9 for beacons >> fwohci0: <Lucent FW322/323> mem 0xe0010000-0xe0010fff irq 19 at device >> 3.0 on pci6 >> fwohci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xe0010000 >> fwohci0: [MPSAFE] >> fwohci0: [ITHREAD] >> fwohci0: OHCI version 1.0 (ROM=0) >> fwohci0: No. of Isochronous channels is 8. >> fwohci0: EUI64 00:90:27:00:01:d0:dc:04 >> fwohci0: Phy 1394a available S400, 2 ports. >> fwohci0: Link S400, max_rec 2048 bytes. >> firewire0: <IEEE1394(FireWire) bus> on fwohci0 >> dcons_crom0: <dcons configuration ROM> on firewire0 >> dcons_crom0: bus_addr 0x41000 >> sbp0: <SBP-2/SCSI over FireWire> on firewire0 >> fwohci0: Initiate bus reset >> fwohci0: fwohci_intr_core: BUS reset >> fwohci0: fwohci_intr_core: node_id=0x00000001, SelfID Count=2, CYCLEMASTER >> mode >> isab0: <PCI-ISA bridge> at device 31.0 on pci0 >> isa0: <ISA bus> on isab0 >> atapci2: <Intel ICH9 SATA300 controller> port >> 0x2438-0x243f,0x2464-0x2467,0x2430-0x2437,0x2460-0x2463,0x2020-0x203f >> mem 0xe0426000-0xe04267ff irq 21 at device 31.2 on pci0 >> atapci2: Reserved 0x20 bytes for rid 0x20 type 4 at 0x2020 >> atapci2: [MPSAFE] >> atapci2: [ITHREAD] >> atapci2: Reserved 0x800 bytes for rid 0x24 type 3 at 0xe0426000 >> atapci2: AHCI called from vendor specific driver >> atapci2: AHCI v1.20 controller with 6 3Gbps ports, PM supported >> atapci2: Caps: 64bit NCQ SNTF ALP AL CLO 3Gbps PM PMD SSC PSC 32cmd >> CCC EM 6ports >> ata5: <ATA channel 0> on atapci2 >> ata5: AHCI reset... >> ata5: hardware reset ... >> ata5: SATA connect time=0ms status=00000123 >> ata5: ready wait time=14ms >> ata5: software reset port 15... >> ata5: ready wait time=0ms >> ata5: SIGNATURE: 00000101 >> ata5: AHCI reset done: devices=00000001 >> ata5: [MPSAFE] >> ata5: [ITHREAD] >> ata6: <ATA channel 1> on atapci2 >> ata6: AHCI reset... >> ata6: hardware reset ... >> ata6: SATA connect time=0ms status=00000123 >> ata6: ready wait time=49ms >> ata6: software reset port 15... >> ata6: ready wait time=0ms >> ata6: SIGNATURE: 00000101 >> ata6: AHCI reset done: devices=00000001 >> ata6: [MPSAFE] >> ata6: [ITHREAD] >> ata7: <ATA channel 2> on atapci2 >> ata7: AHCI reset... >> ata7: hardware reset ... >> ata7: SATA connect time=0ms status=00000123 >> ata7: ready wait time=26ms >> ata7: software reset port 15... >> ata7: ready wait time=0ms >> ata7: SIGNATURE: 00000101 >> ata7: AHCI reset done: devices=00000001 >> ata7: [MPSAFE] >> ata7: [ITHREAD] >> ata8: <ATA channel 3> on atapci2 >> ata8: AHCI reset... >> ata8: hardware reset ... >> ata8: SATA connect timeout status=00000000 >> ata8: AHCI reset done: phy reset found no device >> ata8: [MPSAFE] >> ata8: [ITHREAD] >> ata9: <ATA channel 4> on atapci2 >> ata9: AHCI reset... >> ata9: hardware reset ... >> ata9: SATA connect time=0ms status=00000123 >> ata9: ready wait time=22ms >> ata9: software reset port 15... >> ata9: ready wait time=0ms >> ata9: SIGNATURE: 00000101 >> ata9: AHCI reset done: devices=00000001 >> ata9: [MPSAFE] >> ata9: [ITHREAD] >> ata10: <ATA channel 5> on atapci2 >> ata10: AHCI reset... >> ata10: hardware reset ... >> ata10: SATA connect time=0ms status=00000123 >> ata10: ready wait time=22ms >> ata10: software reset port 15... >> ata10: ready wait time=0ms >> ata10: SIGNATURE: 00000101 >> ata10: AHCI reset done: devices=00000001 >> ata10: [MPSAFE] >> ata10: [ITHREAD] >> ichsmb0: <SMBus controller> port 0x2000-0x201f mem >> 0xe0427000-0xe04270ff irq 18 at device 31.3 on pci0 >> ichsmb0: Reserved 0x20 bytes for rid 0x20 type 4 at 0x2000 >> ichsmb0: [MPSAFE] >> ichsmb0: [ITHREAD] >> smbus0: <System Management Bus> on ichsmb0 >> smb0: <SMBus generic I/O> on smbus0 >> atrtc0: <AT realtime clock> port 0x70-0x71,0x74-0x77 irq 8 on acpi0 >> atrtc0: registered as a time-of-day clock (resolution 1000000us) >> uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 >> ioapic0: routing intpin 4 (ISA IRQ 4) to lapic 0 vector 54 >> uart0: [FILTER] >> uart0: fast interrupt >> uart0: console (115200,n,8,1) >> cpu0: <ACPI CPU> on acpi0 >> coretemp0: <CPU On-Die Thermal Sensors> on cpu0 >> est0: <Enhanced SpeedStep Frequency Control> on cpu0 >> est0: Invalid id16 (set, cur) = (2086, 2346) >> est0: Invalid freq 2664, ignored. >> est0: Invalid id16 (set, cur) = (1826, 2346) >> est0: Invalid freq 2331, ignored. >> est0: Invalid id16 (set, cur) = (1565, 2346) >> est0: Invalid freq 1998, ignored. >> p4tcc0: <CPU Frequency Thermal Control> on cpu0 >> cpu1: <ACPI CPU> on acpi0 >> coretemp1: <CPU On-Die Thermal Sensors> on cpu1 >> est1: <Enhanced SpeedStep Frequency Control> on cpu1 >> est1: Invalid id16 (set, cur) = (2086, 2346) >> est1: Invalid freq 2664, ignored. >> est1: Invalid id16 (set, cur) = (1826, 2346) >> est1: Invalid freq 2331, ignored. >> est1: Invalid id16 (set, cur) = (1565, 2346) >> est1: Invalid freq 1998, ignored. >> p4tcc1: <CPU Frequency Thermal Control> on cpu1 >> isab0: found ICH9 or equivalent chipset: Intel ICH9DO watchdog timer >> isa_probe_children: disabling PnP devices >> ichwd0: <Intel ICH9DO watchdog timer> on isa0 >> isab0: found ICH9 or equivalent chipset: Intel ICH9DO watchdog timer >> ichwd0: Intel ICH9DO watchdog timer (ICH9 or equivalent) >> ichwd0: timer disabled >> atrtc: atrtc0 already exists; skipping it >> sc: sc0 already exists; skipping it >> uart: uart0 already exists; skipping it >> isa_probe_children: probing non-PnP devices >> sc0: <System console> at flags 0x100 on isa0 >> sc0: VGA <16 virtual consoles, flags=0x300> >> sc0: fb0, kbd0, terminal emulator: scteken (teken terminal) >> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 >> atkbdc0 failed to probe at port 0x60 on isa0 >> fdc0 failed to probe at port 0x3f0 irq 6 drq 2 on isa0 >> ppc0 failed to probe at irq 7 on isa0 >> uart1: <ns8250> failed to probe at port 0x2f8-0x2ff irq 3 on isa0 >> isa_probe_children: probing PnP devices >> Device configuration finished. >> Reducing kern.maxvnodes 508766 -> 100000 >> WARNING: ZFS is considered to be an experimental feature in FreeBSD. >> lapic: Divisor 2, Frequency 166747704 hz >> Timecounter "TSC" frequency 3001458636 Hz quality -100 >> Timecounters tick every 1.000 msec >> pflog0: bpf attached >> lo0: firewire0: 2 nodes, maxhop <= 1 cable IRM irm(1) (me) >> firewire0: bus manager 1 >> bpf attached >> ata2: Identifying devices: 00000000 >> ata2: New devices: 00000000 >> ata3: Identifying devices: 00000000 >> ata3: New devices: 00000000 >> ata4: Identifying devices: 00030000 >> ata4: New devices: 00030000 >> usbus0: 12Mbps Full Speed USB v1.0 >> usbus1: 12Mbps Full Speed USB v1.0 >> usbus2: 12Mbps Full Speed USB v1.0 >> usbus3: 480Mbps High Speed USB v2.0 >> usbus4: 12Mbps Full Speed USB v1.0 >> usbus5: 12Mbps Full Speed USB v1.0 >> usbus6: 12Mbps Full Speed USB v1.0 >> usbus7: 480Mbps High Speed USB v2.0 >> ata4-master: pio=PIO4 wdma=WDMA2 udma=UDMA66 cable=80 wire >> ata4-slave: pio=PIO4 wdma=WDMA2 udma=UDMA66 cable=40 wire >> ugen0.1: <Intel> at usbus0 >> uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0 >> ugen1.1: <Intel> at usbus1 >> uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1 >> ugen2.1: <Intel> at usbus2 >> uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2 >> ugen3.1: <Intel> at usbus3 >> uhub3: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3 >> ugen4.1: <Intel> at usbus4 >> uhub4: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4 >> ugen5.1: <Intel> at usbus5 >> uhub5: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5 >> ugen6.1: <Intel> at usbus6 >> uhub6: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6 >> ugen7.1: <Intel> at usbus7 >> uhub7: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus7 >> ZFS filesystem version 13 >> ZFS storage pool version 13 >> acd0: <PIONEER DVD-RW DVR-110D/1.37> DVDR drive at ata4 as master >> acd0: read 6890KB/s (6890KB/s) write 5511KB/s (6890KB/s), 2000KB buffer, >> UDMA66 >> acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet >> acd0: Writes: CDR, CDRW, DVDR, test write, burnproof >> acd0: Audio: play, 256 volume levels >> acd0: Mechanism: ejectable tray, unlocked >> acd0: Medium: no/blank disc >> acd1: DMA limited to UDMA33, device found non-ATA66 cable >> acd1: <DVD-ROM BDV316G/VER 0C17> DVDROM drive at ata4 as slave >> acd1: read 687KB/s (8251KB/s), 512KB buffer, UDMA33 >> acd1: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet >> acd1: Writes: >> acd1: Audio: play, 256 volume levels >> acd1: Mechanism: ejectable tray, unlocked >> acd1: Medium: no/blank disc >> ata5: Identifying devices: 00000001 >> ata5: New devices: 00000001 >> ata5-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire >> ad10: 476940MB <WDC WD5000AAKS-00YGA0 12.01C02> at ata5-master SATA300 >> ad10: 976773168 sectors [969021C/16H/63S] 16 sectors/interrupt 1 depth >> queue >> GEOM: new disk ad10 >> ad10: Intel check1 failed >> ad10: Adaptec check1 failed >> ad10: LSI (v3) check1 failed >> ad10: LSI (v2) check1 failed >> ad10: FreeBSD check1 failed >> ata6: Identifying devices: 00000001 >> ata6: New devices: 00000001 >> ata6-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire >> ad12: 476940MB <Seagate ST3500630AS 3.AAK> at ata6-master SATA300 >> ad12: 976773168 sectors [969021C/16H/63S] 16 sectors/interrupt 1 depth >> queue >> GEOM: new disk ad12 >> firewire0: New S400 device ID:001f5bfffe2776a6 >> fwohci0: txd err= 3 miss Ack err >> ad12: Intel check1 failed >> ad12: Adaptec check1 failed >> ad12: LSI (v3) check1 failed >> ad12: LSI (v2) check1 failed >> ad12: FreeBSD check1 failed >> ata7: Identifying devices: 00000001 >> ata7: New devices: 00000001 >> ata7-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire >> ad14: 238475MB <WDC WD2500KS-00MJB0 02.01C03> at ata7-master SATA300 >> ad14: 488397168 sectors [484521C/16H/63S] 16 sectors/interrupt 1 depth >> queue >> GEOM: new disk ad14 >> ad14: Intel check1 failed >> ad14: Adaptec check1 failed >> ad14: LSI (v3) check1 failed >> ad14: LSI (v2) check1 failed >> ad14: FreeBSD check1 failed >> ata8: Identifying devices: 00000000 >> ata8: New devices: 00000000 >> ata9: Identifying devices: 00000001 >> ata9: New devices: 00000001 >> ata9-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire >> ad18: 715404MB <Seagate ST3750640AS 3.AAE> at ata9-master SATA300 >> ad18: 1465149168 sectors [1453521C/16H/63S] 16 sectors/interrupt 1 depth >> queue >> GEOM: new disk ad18 >> ad18: Intel check1 failed >> uhub0: 2 ports with 2 removable, self powered >> uhub1: 2 ports with 2 removable, self powered >> uhub2: 2 ports with 2 removable, self powered >> ad18: Adaptec check1 failed >> uhub4: 2 ports with 2 removable, self powered >> ad18: LSI (v3) check1 failed >> uhub5: 2 ports with 2 removable, self powered >> uhub6: 2 ports with 2 removable, self powered >> ad18: LSI (v2) check1 failed >> ad18: FreeBSD check1 failed >> ata10: Identifying devices: 00000001 >> ata10: New devices: 00000001 >> ata10-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire >> ad20: 715404MB <Seagate ST3750640AS 3.AAE> at ata10-master SATA300 >> ad20: 1465149168 sectors [1453521C/16H/63S] 16 sectors/interrupt 1 depth >> queue >> GEOM: new disk ad20 >> ad20: Intel check1 failed >> ad20: Adaptec check1 failed >> ad20: LSI (v3) check1 failed >> ad20: LSI (v2) check1 failed >> ad20: FreeBSD check1 failed >> (probe0:sbp0:0:0:0): error 22 >> (probe0:sbp0:0:0:0): Unretryable Error >> (probe1:sbp0:0:1:0): error 22 >> (probe1:sbp0:0:1:0): Unretryable Error >> (probe2:sbp0:0:2:0): error 22 >> (probe2:sbp0:0:2:0): Unretryable Error >> (probe3:sbp0:0:3:0): error 22 >> (probe3:sbp0:0:3:0): Unretryable Error >> (probe4:sbp0:0:4:0): error 22 >> (probe4:sbp0:0:4:0): Unretryable Error >> (probe5:sbp0:0:5:0): error 22 >> (probe5:sbp0:0:5:0): Unretryable Error >> (probe6:sbp0:0:6:0): error 22 >> (probe6:sbp0:0:6:0): Unretryable Error >> ATA PseudoRAID loaded >> SMP: AP CPU #1 Launched! >> cpu1 AP: >> ID: 0x01000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff >> lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff >> timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00000400 >> ioapic0: routing intpin 9 (ISA IRQ 9) to lapic 1 vector 48 >> ioapic0: routing intpin 18 (PCI IRQ 18) to lapic 1 vector 49 >> ioapic0: routing intpin 21 (PCI IRQ 21) to lapic 1 vector 50 >> WARNING: WITNESS option enabled, expect reduced performance. >> Root mount waiting for: usbus7 usbus3 >> Root mount waiting for: usbus7 usbus3 >> uhub3: 6 ports with 6 removable, self powered >> uhub7: 6 ports with 6 removable, self powered >> ugen3.2: <vendor 0x0781> at usbus3 >> umass0: <vendor 0x0781 product 0x5406, class 0/0, rev 2.00/2.00, addr >> 2> on usbus3 >> umass0: SCSI over Bulk-Only; quirks = 0x0000 >> Root mount waiting for: usbus3 >> umass0:1:0:-1: Attached to scbus1 >> (probe0:umass-sim0:0:0:0): Down reving Protocol Version from 2 to 0? >> GEOM: new disk da0pass0 at umass-sim0 bus 0 target 0 lun 0 >> >> pass0: <SanDisk Cruzer 8.02> Removable Direct Access SCSI-0 device >> pass0: 40.000MB/s transfers >> da0 at umass-sim0 bus 0 target 0 lun 0 >> da0: <SanDisk Cruzer 8.02> Removable Direct Access SCSI-0 device >> da0: 40.000MB/s transfers >> da0: 3859MB (7905279 512 byte sectors: 255H 63S/T 492C) >> Trying to mount root from zfs:alert >> ugen5.2: <vendor 0x1241> at usbus5 >> ukbd0: <vendor 0x1241 product 0x1603, class 0/0, rev 1.10/2.80, addr >> 2> on usbus5 >> kbd: new array size 4 >> kbd1 at ukbd0 >> kbd1: ukbd0, generic (0), config:0x0, flags:0x3d0000 >> ugen2.2: <American Power Conversion> at usbus2 >> ct_to_ts([2009-07-09 12:36:12]) = 1247142972.000000000 >> start_init: trying /sbin/init >> lock order reversal: >> 1st 0xffffffff80815040 pf task mtx (pf task mtx) _at_ >> /usr/src/sys/contrib/pf/net/pf_ioctl.c:1394 >> 2nd 0xffffffff809f7b40 ifnet (ifnet) _at_ /usr/src/sys/net/if.c:1887 >> KDB: stack backtrace: >> db_trace_self_wrapper() at db_trace_self_wrapper+0x2a >> _witness_debugger() at _witness_debugger+0x49 >> witness_checkorder() at witness_checkorder+0x7d2 >> _rw_rlock() at _rw_rlock+0x60 >> ifunit() at ifunit+0x22 >> pfioctl() at pfioctl+0x20ea >> devfs_ioctl_f() at devfs_ioctl_f+0x6e >> kern_ioctl() at kern_ioctl+0xbc >> ioctl() at ioctl+0xf0 >> syscall() at syscall+0x18b >> Xfast_syscall() at Xfast_syscall+0xd0 >> --- syscall (54, FreeBSD ELF64, ioctl), rip = 0x80098a88c, rsp = >> 0x7fffffffb5c8, rbp = 0x7fffffffb710 --- >> lock order reversal: >> 1st 0xffffff0074026098 zfs (zfs) _at_ /usr/src/sys/kern/vfs_mount.c:1054 >> 2nd 0xffffff007417dba8 devfs (devfs) _at_ /usr/src/sys/kern/vfs_subr.c:2083 >> KDB: stack backtrace: >> db_trace_self_wrapper() at db_trace_self_wrapper+0x2a >> _witness_debugger() at _witness_debugger+0x49 >> witness_checkorder() at witness_checkorder+0x7d2 >> __lockmgr_args() at __lockmgr_args+0xc92 >> vop_stdlock() at vop_stdlock+0x39 >> VOP_LOCK1_APV() at VOP_LOCK1_APV+0xc2 >> _vn_lock() at _vn_lock+0x50 >> vget() at vget+0x6c >> devfs_allocv() at devfs_allocv+0xee >> devfs_root() at devfs_root+0x41 >> vfs_donmount() at vfs_donmount+0xf93 >> nmount() at nmount+0x74 >> syscall() at syscall+0x18b >> Xfast_syscall() at Xfast_syscall+0xd0 >> --- syscall (378, FreeBSD ELF64, nmount), rip = 0x8007aaffc, rsp = >> 0x7fffffffdd28, rbp = 0x800a04048 --- >> >> Thanks, >> >> Chris >> -- >> _at_chrisattack >> ----------------------------------------- >> http://twitter.com/chrisattack >> http://chrisattack.com >> _______________________________________________ >> freebsd-current_at_freebsd.org mailing list >> http://lists.freebsd.org/mailman/listinfo/freebsd-current >> To unsubscribe, send any mail to "freebsd-current-unsubscribe_at_freebsd.org >> " >> > >Received on Thu Jul 09 2009 - 22:13:36 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:39:51 UTC